manualshive.com logo in svg

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Share
Download
Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 95

Executing the fan test via ServerView Operations Manager

▶

Open the ServerView Operations Manager and log in.

▶

Under 

Administration

 select 

Server Configuration

.

▶

In the hierarchy tree of the 

Server list

 tab, select the server to be

configured.

▶

In the right-hand side of the window, specify the details on the selected
server and confirm your entries by clicking 

GO...

. In the left-hand section of

the window, the 

Configuration

 tab is being activated.

▶

In the navigation area of the 

Configuration

 tab, select 

Other Settings

.

▶

Under 

Daily Fan Test

, set the daily fan test time to a few minutes from the

current time. (Ensure to note down your previous setting.)

▶

Click 

Save Page

.

The fan test will be started at the specified time.

▶

After the fan test is complete, restore the time setting to its initial value and
click 

Save Page

.

In case of maintenance done by Fujitsu engineers in Japan:
Executing the fan test via Chassis ID Prom Tool

Please follow the instructions provided separately.

5.2.6

Updating Server View RAID Manager

For the spare parts of the product compatible parts equal to the original parts
might be used. If an old version of the ServerView RAID Manager is used, the
SSD life monitoring function does not work correctly after replacement. Please
always use the latest version of the ServerView RAID Manager.

https://www.fujitsu.com/fts/support/

For Japan:

https://www.fujitsu.com/jp/products/computing/servers/primergy/downloads/

Basic software procedures

CX400 M6

Upgrade and Maintenance Manual

95

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands