manualshive.com logo in svg

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Share
Download
Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 134

Installing the HDD/SSD bridge board

Figure 98: Installing the HDD/SSD bridge board

▶

Use the two guide pins on the chassis to align the bridge board and slowly
place it into the chassis (1).

▶

Secure the HDD/SSD bridge board to the chassis with the screws (2).

▶

Place the air duct on the HDD/SSD bridge board and secure it with a
hexagonal spacer (3).

▶

Secure the HDD/SSD bridge board with a hexagonal spacer (4).

Concluding steps

▶

"Installing the power distribution board kit" on page 161

.

▶

Install all HDD backplanes, see 

"Installing the 2.5-inch HDD backplane" on 

page 124

.

▶

"Installing the fan cage" on page 126

.

▶

Install all fan modules, see 

"Installing the fan module" on page 148

.

▶

"Installing the new high speed riser module" on page 153

.

Hard disk drive (HDD) / solid state disk (SSD)

134

Upgrade and Maintenance Manual

CX400 M6

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands