Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 202

Page: 202 / 209

Error indicator (2)

Status

Description

off

No HDD/SSD error detected.

orange on

An HDD/SSD error has been detected.

Possible causes:

– The drive is defective and needs replacing.

– A RAID rebuild process has failed.

– The HDD/SSD module has not been inserted correctly.

flashing orange
slowly

HDD/SSD RAID rebuild is in progress. Data is being
restored after replacing a drive that has been combined
into a RAID array.

13.2.2

Server enclosure rear

13.2.2.1

Indicator on hot-plug PSU

Figure 166: Indicator on hot-plug PSU

PSU status indicator

Appendix A

202

Upgrade and Maintenance Manual

CX400 M6

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Search results

Summary of Contents for PRIMERGY CX400 M6

Reviews:

Brands by name

Popular brands

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Search results

Summary of Contents for PRIMERGY CX400 M6

Reviews:

Brands by name

Popular brands