manualshive.com logo in svg

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Share
Download
Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 88

Using the Infrastructure Manager

▶

To switch on the ID indicator from the Infrastructure Manager, select a node
from the 

Node List

 screen and operate ID LED from the 

Action

 button.

5.2

Completing the maintenance task

5.2.1

Verifying system information backup or restore

System information, such as chassis type, serial number, and manufacturing
data, is stored in the Chassis FRU ROM on the power distribution board. To
avoid loss of system information when replacing the power distribution board, a
backup copy of the data is automatically stored in the system board ID
EPROM. After replacing the power distribution board, the backup data is
restored from the system board to the new power distribution board
automatically.

In order to verify whether the restore process has been successful, check the
System Event Log (SEL), see 

"Viewing and clearing the System Event Log 

(SEL)" on page 91

.

When using the Infrastructure Manager, please refer to the following
manuals about backup and restore function of system information.

See manual "FUJITSU Software Infrastructure Manager Vx.x.x User's
Guide", section "2.10 Backup/Restore Hardware Settings", available at:

https://ts.fujitsu.com/support/

For Japan:
See manual "FUJITSU Software Infrastructure Manager Vx.x.x 

解説書

",

section "2.10 

ハードウェア設定バックアップ／リストア機能

", available at:

https://www.fujitsu.com/jp/products/software/infrastructure-software/
infrastructure-software/serverviewism/technical/

Basic software procedures

88

Upgrade and Maintenance Manual

CX400 M6

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands