manualshive.com logo in svg

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Share
Download
Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 116

RAID level

Procedure

RAID 0

CAUTION

RAID 0 provides no data redundancy.

In case of an HDD module is defect, all
data are lost!

RAID 1

RAID 5

Removing an HDD/SSD module from a RAID 1 or
RAID 5 array will not result in data loss. However,
the removed drive needs to be replaced
immediately by an HDD/SSD module of the same
or larger capacity.

After replacing the HDD/SSD module,
RAID rebuild will be performed as a
background process, see 

"Performing a 

RAID array rebuild" on page 89

.

In order to permanently remove an operational HDD/SSD module that is part of
a RAID array from the server, you first need to delete the array using
ServerView RAID Manager.

CAUTION

All data on all HDDs/SSDs in the array will be lost when deleting the
RAID array!

▶

Be sure to back up your data before deleting a RAID array.

▶

For more information, see the "ServerView Suite RAID
Management" user guide.

Removing a 2.5-inch HDD/SSD module

▶

Pinch the green locking clips and open the locking lever (see 

Figure 79

).

▶

Pull the HDD/SSD module out a few centimeters.

▶

Wait about 30 seconds.

This period is necessary for the RAID controller to recognize that an
HDD module has been removed and for the HDD to come to a stop.

This period is necessary for the RAID controller to recognize that an
SSD module has been removed.

Hard disk drive (HDD) / solid state disk (SSD)

116

Upgrade and Maintenance Manual

CX400 M6

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands