manualshive.com logo in svg

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Share
Download
Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 94

Please refer to the following manuals of Infrastructure Manager for
collecting logs from ISM.

See manual "FUJITSU Software Infrastructure Manager Vx.x.x User's
Guide", section "2.5 Log Management", available at:

https://ts.fujitsu.com/support/

For Japan:
See manual "FUJITSU Software Infrastructure Manager Vx.x.x 

解説書

",

section "2.5 

ログ管理機能

", available at:

https://www.fujitsu.com/jp/products/software/infrastructure-software/
infrastructure-software/serverviewism/technical/

5.2.5

Performing a fan test

Notes on replacing a defective fan

After replacing a defective system fan or PSU containing a defective fan,
the fan error indicators will stay lit until the next fan test. By default, a fan
test is automatically started every 24 hours. The first automatic fan test
being performed after replacing a fan will turn off the fan error indicator.

If you want to start the fan test manually, you can do so by following the
description below:

Executing the fan test via the iRMC S5 web interface

▶

Log into the iRMC S5 web interface.

The 

System

 menu is displayed on default.

▶

Open the 

Cooling

 page.

▶

Expand the 

Cooling Devices

 group.

▶

Click 

Start Fan Test

.

For more information on iRMC settings, see the iRMC user guides.

Basic software procedures

94

Upgrade and Maintenance Manual

CX400 M6

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands