manualshive.com logo in svg

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Share
Download
Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 187

▶

If applicable, remove all 2.5-inch HDD/SSD dummy modules until slot 6 from
the left from the relevant HDD/SSD cage, see 

"Removing a 2.5-inch HDD/

SSD dummy module" on page 113

.

▶

"Extending the server enclosure out of the rack" on page 49

.

▶

If applicable, remove the front bezel mounted on the left end, see

"Removing the HDD/SSD x6 front bezel" on page 140

.

▶

If applicable, remove the front bezel mounted on the left end, see

"Removing the HDD/SSD x4 front bezel" on page 141

.

▶

"Removing the top covers" on page 54

.

▶

Remove the left high speed riser module, see 

"Removing the defective high 

speed riser module" on page 151

.

Removing the thermal cable

Figure 152: Removing the thermal cable (A)

▶

Disconnect the cable from the PDB and remove the cable from the clamp
(see circles).

Front panel

CX400 M6

Upgrade and Maintenance Manual

187

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands