manualshive.com logo in svg

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Share
Download
Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 165

11

Front panel

11.1

Safety notes

CAUTION

▶

When inserting the front panel module into the server enclosure,
ensure not to pinch or strain any connected cables.

▶

Circuit boards and soldered parts of internal options are exposed
and can be damaged by static electricity. Always discharge static
build-up (e.g. by touching a grounded object) before handling
electrostatic-sensitive devices (ESDs).

▶

Do not touch the circuitry on boards or soldered parts. Hold circuit
boards by their metallic areas or edges.

▶

For more information, see 

"Important information" on page 25

.

11.2

Front panel module

11.2.1

Replacing the left front panel module

Field Replaceable Unit
(FRU)

Hardware: 5 minutes

Tools:

Preliminary and concluding steps: tool-less

Main steps: Phillips PH2 / (+) No. 2

Preliminary steps

▶

"Shutting down the server" on page 41

.

▶

"Disconnecting the power cord" on page 42

.

▶

If applicable, remove the front bezel, see 

"Removing the front bezel" on 

page 48

.

CX400 M6

Upgrade and Maintenance Manual

165

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands