manualshive.com logo in svg

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Share
Download
Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 41

Possibilities to get more information about the defective component

–

Checking the ServerView System Monitor, available on Windows or Linux
based servers with ServerView agents installed.

For more information, see the "ServerView System Monitor" user
guide.

–

Checking the System Event Log (SEL), see 

"Viewing and clearing the 

System Event Log (SEL)" on page 91

.

–

Checking the indicators on the components, see 

"Connectors and 

indicators" on page 198

.

4.2

Shutting down the server

CAUTION

▶

For more information, see 

"Important information" on page 25

.

This step is only required when upgrading or replacing non-hot-plug
components.

▶

Inform the system administrator that the server will be shut down and put
offline.

▶

Terminate all applications.

▶

Perform the required procedures described in the preliminary steps of each
upgrade or maintenance task.

▶

Shut down the server.

If the system is running an ACPI-compliant operating system (OS),
pressing the On/Off button will perform a graceful shutdown.

Power button override

The server node can be switched off (hard power off) by holding
down the On/Off button (approximately 4 - 5 seconds). However, if
you turn off the power in this way, the system will turn on
automatically after a few seconds.

Basic hardware procedures

CX400 M6

Upgrade and Maintenance Manual

41

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands