manualshive.com logo in svg

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Share
Download
Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 103

Ensure that the PSU engages correctly in the bay and is locked in
position. This is the only way to prevent the PSU from sliding out of its
bay and being damaged during transportation.

Concluding steps

▶

Connect the power cord to the new PSU and secure it with a cable clamp,
see 

"Connecting the power cord" on page 84

.

▶

Only when replacing a PSU in a non-redundant configuration: 

"Switching on 

the server nodes" on page 86

.

▶

"Performing a fan test" on page 94

.

6.4

Removing/installing the PSU dummy
module

Customer Replaceable
Unit (CRU)

Hardware: 5 minutes

Tools:

tool-less

CAUTION

Excessive temperatures could damage system components.

▶

Never leave the bay for the hot-plug PSU empty for more than two
minutes during operation.

Power supply unit (PSU)

CX400 M6

Upgrade and Maintenance Manual

103

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands