Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download

Page: 15 / 209

Before you start

2.1

Basic information

2.1.1

Proceeding

Before you start any upgrade or maintenance task, proceed as follows:

▶

Carefully read the safety instructions, see

"Important information" on

page 25

▶

Make sure that all necessary manuals are available, see

"Documentation

overview" on page 21

. Print the PDF files if required.

▶

Make yourself familiar with the procedure categories, see

"Classification of

procedures" on page 16

▶

Ensure that all required tools are available, see

"Tools you need at hand" on

page 20

2.1.2

Advanced Thermal Design (ATD)

The ATD option allows you to operate the system with a wider temperature
range either of 5 °C to 40 °C, depending on your system and configuration.

This option can only be ordered from the manufacturer and is
indicated by the respective logo on the identification rating plate.

CAUTION

▶

In a system that is configured with ATD, only certain components
which support the respectively increased higher operating
temperature range may be installed and used. For applicable
restrictions, see the official configurator tool.

CX400 M6

Upgrade and Maintenance Manual

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Search results

Summary of Contents for PRIMERGY CX400 M6

Reviews:

Related manuals for PRIMERGY CX400 M6

Brands by name

Popular brands

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Search results

Summary of Contents for PRIMERGY CX400 M6

Reviews:

Related manuals for PRIMERGY CX400 M6

Brands by name

Popular brands