manualshive.com logo in svg

Freescale Semiconductor ColdFire MCF5211, Reference Manual

Share
Download
Freescale Semiconductor ColdFire MCF5211 Reference Manual Download Page 303

General Purpose Timer Module (GPT)

MCF5213 ColdFire® Integrated Microcontroller Reference Manual, Rev. 3

Freescale Semiconductor

18-21

 

18.8

Reset

Reset initializes the GPT registers to a known startup state as described in 

Section 18.6, “Memory Map 

and Registers

.”

18.9

Interrupts

Table 18-24

 lists the interrupt requests generated by the timer.

18.9.1

GPT Channel Interrupts (C

n

F)

A channel flag is set when an input capture or output compare event occurs. Clear a channel flag by writing 
a 1 to it.

NOTE

When the fast flag clear all bit (GPTSCR1[TFFCA]) is set, an input capture 
read or an output compare write clears the corresponding channel flag.

When a channel flag is set, it does not inhibit subsequent output compares 
or input captures

18.9.2

Pulse Accumulator Overflow (PAOVF)

PAOVF is set when the 16-bit pulse accumulator rolls over from 0xFFFF to 0x0000. If the PAOVI bit in 
GPTPACTL is also set, PAOVF generates an interrupt request. Clear PAOVF by writing a 1 to this flag.

NOTE

When the fast flag clear all enable bit (GPTSCR1[TFFCA]) is set, any 
access to the pulse accumulator counter registers clears all the flags in 
GPTPAFLG.

6

A successful output compare on channel 3 causes an output value determined by OC3D

n

 value to temporarily override the 

output compare pin state of any other output compare channel.The next OC action for the specific channel continues to be 
output to the pin. A channel 3 output compare can cause bits in the output compare 3 data register to transfer to the GPT port 
data register, depending on the output compare 3 mask register.

Table 18-24. GPT Interrupt Requests

Interrupt Request

Flag

Enable Bit

Channel 3 IC/OC

C3F

C3I

Channel 2 IC/OC

C2F

C2I

Channel 1 IC/OC

C1F

C1I

Channel 0 IC/OC

C0F

C0I

PA overflow

PAOVF

PAOVI

PA input

PAIF

PAI

Timer overflow

TOF

TOI

Summary of Contents for ColdFire MCF5211

































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands