manualshive.com logo in svg

Freescale Semiconductor ColdFire MCF5211, Reference Manual

Share
Download
Freescale Semiconductor ColdFire MCF5211 Reference Manual Download Page 177

MCF5213 ColdFire® Integrated Microcontroller Reference Manual, Rev. 3

Freescale Semiconductor

11-1

 

Chapter 11  
General Purpose I/O Module

11.1

Introduction

Many of the pins associated with the external interface may be used for several different functions. When 
not used for their primary function, many of the pins may be used as general-purpose digital I/O pins. In 
some cases, the pin function is set by the operating mode, and the alternate pin functions are not supported. 

The digital I/O pins are grouped into 8-bit ports. Some ports do not use all 8 bits. Each port has registers 
that configure, monitor, and control the port pins. 

Figure 11-1

 is a block diagram of the MCF5213 ports. 

 

Figure 11-1. General Purpose I/O Module Block Diagram

DDATA[3:0] / PDD[7:4]

PORT QS

PORT AS

PORT DD

PORT UA

PORT UC

PORT TC

PORT TD

PST[3:0] / PDD[3:0]

SDA / PAS[1] / CANRX / RXD2
SCL / PAS[0] / CANTX / TXD2

QSPI_SCK / PQS[2] / SCL / RTS1
QSPI_DIN / PQS[1] / CANRX / RXD1
QSPI_DOUT / PQS[0] / CANTX RXD0

DTIN3 / PTC[3] / DTOUT3 / PWM6
DTIN2 / PTC[2] / DTOUT2 / PWM4
DTIN1 / PTC[1] / DTOUT1 / PWM2
DTIN0 / PTC[0] / DTOUT0 / PWM0

CTS1 / PUB[3] / SYNCA / RXD2
RTS1 / PUB[2] / SYNCB / TXD2
RXD1 / PUB[1]
TXD1 / PUB[0]

CTS0 / PUA[3] / CANRX
RTS0 / PUA[2] / CANTX
RXD0 / PUA[1]
TXD0 / PUA[0]

CTS2 / PUC[3]
RTS2 / PUC[2]
RXD2 / PUC[1]
TXD2 / PUC[0]

PWM7 / PTD[3]
PWM5 / PTD[2]
PWM3 / PTD[1]
PWM1 / PTD[0]

PORT TA

GPT[3] / PTA[3] / PWM7
GPT[2] / PTA[2] / PWM5
GPT[1] / PTA[1] / PWM3
GPT[0] / PTA[0] / PWM1

PORT AN

AN0 / PAN[0]
AN1 / PAN[1]

AN2 / PAN[2]
AN3 / PAN[3]

AN4 / PAN[4]
AN5 / PAN[5]

AN6 / PAN[6]
AN7 / PAN[7]

PORT UB

QSPI_CS0 / PQS[3] / SDA / CTS1

PORT NQ

IRQ1 / PNQ[1] / SYNCA / PWM1

IRQ2 / PNQ[2]
IRQ3 / PNQ[3]
IRQ4 / PNQ[4]

IRQ5 / PNQ[5]
IRQ6 / PNQ[6]
IRQ7 / PNQ[7]

QSPI_CS1 / PQS[4]

QSPI_CS2 / PQS[5]

QSPI_CS3 / PQS[6] / SYNCA / SYNCB 

Summary of Contents for ColdFire MCF5211

































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands