Farmet FALCON 3 Operating Manual Download | Manualshive

Page: 97 / 99

background image

Manual

FALCON 3 | 4 | 6 | 8

97

│

99

18.6.

RECOMMENDED TIGHTENING TORQUES OF BOLTING

BOLTING

TIGHTENING

TORQUES

NOTE

M8x1

8Nm

Fastening screws of house bearings

M8 (8.8)

25Nm

M12 (8.8)

87Nm

Share screws

M16 (8.8)

210Nm

House bearings

M 20 (8.8)

50Nm

Rotary harrowing screws

M20 (8.8)

410Nm

Protection screws, axle rubber-tyred roller wheels

M24 (8.8)

710Nm

Hopper screws

HYD AIR JOINTS

M16x1,5

60Nm

Hydraulic screwing, air screwing

M22x1,5

140Nm

Hydraulic screwing, air screwing

19.

STORING THE MACHINE

When you put the machine out of operation for a longer-period of time:



Store the machine under a roof, if possible.



Store the machine on an even and solid ground with sufficient bearing capacity.



Clean the machine before storing and make sure that the machine is not damaged during the storage. Pay
special attention to all labelled lubricating places and lubricate the machine according to the lubrication plan.



Store the machine with folded frames in the transport position. Leave the machine on the axle and the
standing leg; secure the machine against movement with wedges or other suitable instruments.



The machine must not be leaning on the discs as they may get damaged.



Prevent access by unauthorized persons to the machine.

20.

PROTECTION OF ENVIRONMEN



Check the tightness of the hydraulic system regularly.



Replace or repair hydraulic tubes or other parts of the hydraulic system showing signs of damage, before oil
starts to leak.



Check the condition of hydraulic tubes and execute their timely replacement. The usable life of hydraulic
tubes also includes the storage time.



Deal with oils and fats according to valid acts and regulations on wastes.

21.

DISPOSAL OF THE MACHINE AFTER THE END OF ITS USABLE LIFE



The operator must make sure that the steel parts and parts in which the hydraulic oil or lubricant is used are
separated for disposal.



The operator will cut the steel parts according to safety regulations and hand them over to the scrap yard for
secondary raw materials. For other parts follow the valid acts on wastes.

«
...
95
96
97
98
99
»

Summary of Contents for FALCON 3




































































































Reviews:

No comments

Related manuals for FALCON 3

ACS880-01 Series

Brand: ABB Pages: 238

Brand: CAIRE Pages: 2

Brand: Fisher Scientific Pages: 42

Synthesis SDEC-3000

Brand: JBL Pages: 24

Brand: Xilica Audio Design Pages: 30

Brand: Labelmate Pages: 61

Brand: Labconco Pages: 62

Brand: Quincy Pages: 31

Lyme FIA Sofia 2

Brand: Quidel Pages: 49

Brand: Quest Leisure Products Pages: 12

Brand: Vapotherm Pages: 32

Brand: Vanguard Instruments Pages: 47

Brand: Xtool Pages: 8

Brand: Yamaha Pages: 48

Brand: Yamaha Pages: 85

Brand: Yamaha Pages: 43

Brand: Yamaha Pages: 200

Brand: Goobay Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands