2.
41
(MT13 - En 2015)
2
CD2131÷CD2138 press the button you want
to assign to the user on the push-button
keyboard. When the call is received, the
videointercom is programmed automatically,
you hear the call tone in the loudspeaker and
the videointercom is turned on, showing the
calling external station. Close and pick up the
handset to start a conversation with the
external door station and verify the correct
working mode of the equipment;
programming mode is signalled on the
external door station by an acknowledge
tone if accepted or a dissuasion tone if
rejected;
repeat programming phases for all the
videointercoms connected to the system.
Manual programming
The manual programming mode allows you to
enter the user address, assign the internal
address and codes to buttons from 1 to 5 and
"
" (example of programming to page 2.45).
Using the push-buttons for programming
Press button "
", "
" and "1" to enter
addresses or codes.
: Press this button to confirm address or
code programming or go to the next
programming step.
: Press this button to confirm the digit just
dialled and to proceed to enter next digit
in the following order: hundreds, tens, units.
1 :
Press this button to increase the value
you want to enter. Press the button for a
number of times equal to the digit you want
to enter (digit 1 = 1 time; digit 9 = 9 times;
digit 0 = 10 times).
Entering codes or addresses
- Codes and/or addresses must have three
digits (hundreds, tens, units); codes and/or
addresses with tens and units or units only
must be completed by adding zeros. For
example, address 96 will become 096 and
address 5 will become 005.
- Digits must be entered individually (beginning
from the hundred), by pressing the button “1”
for a number of times “n”, where “n” is the
value of the digit you want to enter. Store the
digit pressing the button "
"; a tone will
confirm the acquisition of the 1
st
digit.
- Follow the same procedure to store the 2nd
and 3rd digit.
For example, to enter code 096 you must:
- press button “1” 10 times to enter digit 0 and
press the button “
”; you will get a tone on the
loudspeaker;
- press button “1” 9 times to enter digit 9 and
press the button “
”; you will get a tone on the
loudspeaker;
- press button “1” 6 times to enter digit 6 and
press the button “
”; you will get a tone on the
loudspeaker.
Programming of the user address and
internal address
- User address – this code allows you to
receive an external call, turn on the
videointercom, have a conversation and open
the door at the calling external station.
- Internal address – these codes are used to
identify the videointercoms installed in the
apartment (max.6). In case of one
videointercom only, the internal code must
be 000 (default value); if other videointercoms
are present (max. other 5) you must assign to
them the codes 001, 002, 003 etc.
Programming these addresses all the
videointercoms will ring-UP when receiving
an external, intercommunicating or floor
(local) call (if programmed).
To program the user address and internal
address it is necessary to:
enter the programming mode following
the instructions described in “Enter the
programming mode”;
keep pressed the button
for more than 4
seconds; yellow LED starts flashing;
enter the 3 digit of the user address following
the procedure reported on the paragraph
“Entering codes or addresses”;
press the button
to confirm the present
phase and move to the next phase which is:
programming of the internal address; an
acknowledge tone will be heard;
enter the 3 digit of the internal address
following the procedure reported on the
paragraph “Entering codes or addresses”;
press the button
to confirm; an acknowl-
edge tone will be heard and the yellow LED
lights-ON continuously;
proceed with another programming phase
or exit the programming mode by hanging up
the handset.
Note. If one of the two above mentioned
addresses is already correctly programmed
and you don’t want to program it again it would
be possible to skip its programming by simply
pressing button
.
Programming address to be stored to
each button
Button “
”. To this button can be stored the
addresses of maximum 4 external stations
which can be connected sequentially. In this
way the user can monitor, communicate or
open the door of 4 different external stations
without being called from them but simply
pressing several times the button
. In the
case of a system with only 1 external door
station it isn’t necessary to store any
address because it will be acquired
automatically at the first call.
To make the programming it necessary to:
enter the programming mode following
the instructions described in “Enter the
programming mode”;
keep pressed the button "
" for more than 4
seconds; yellow LED starts flashing;
enter the 3 digit of the address of the 1st
external door station to be stored (codes
from 231 to 250) following the procedure
reported on the paragraph “Entering codes
or addresses”;
press the button
to confirm the present
address move to the 2nd one; an acknowl-
edge tone will be heard;
enter the 3 digit of the address of the 2nd
external door station and confirm by press-
ing button
;
proceed entering the addresses of the 3rd
and 4th external stations (if present) or exit
the present programming phase pressing
several times the button
, you will be led
back to selecting programming mode;
proceed with another programming or exit
the programming mode by hanging up the
handset.
Note: store only the addresses of the ex-
ternal door stations to which the user can
be connected. Don’t store the addresses
of external door stations belonging to dif-
ferent buildings even if in the same instal-
lation.
Buttons 1, 2, 3, 4 and 5.
These buttons can be used to:
make intercommunicating calls;
- to call users of different apartments it is
necessary to store in each button of your
monitor the address of the user you wish to
call pressing that button (codes from 001 to
200).
- to call other videointercoms installed in the
same apartment (local intercommunicating
service), it is necessary to store in the buttons
1, 2, 3, 4, 5 of each monitor always the code
000; starting from button 1 and going on until
you have programmed, with the code 000,
as many buttons as are the videointercoms
installed in the apartment (max 6 units) you
wish to call; automatically by pressing buttons
1,2,3,4,5 of one unit you will call the unit
whose internal address is related to the
pressed button according to table 3. For
example if you press the button 3 from the
videointercom whose intercommunicating
address is 002 you will call the user with
intercommunicating address 003.
monitoring external door stations (it is
suggested to use button
to monitor the 1
st
external door station) to enable this feature
store the address of the external door station
(codes from 231 to 250).
optional functions operated by means
of the actuators art.2281; to enable this
functions store the address of the actuator to
be operated (codes from 211 to 220).
To make the programming it is necessary:
enter the programming mode following
the instructions described in “Enter the
programming mode”;
a - keep pressed for more than 4 seconds
the button you wish to program; yellow LED
starts flashing;
b -enter the 3 digit of the code or address
you wish to store following the procedure
reported on the paragraph “Entering codes
or addresses”;
c -press the button
; an acknowledge
tone will be heard and the yellow LED lights-
ON continuously;
repeat phases a-b-c to program other but-
tons or exit the programming mode by hang-
ing up the handset; yellow LED turns-OFF.
Notes.
- In each button can be stored only one code or
address.
INTERNAL STATIONS
