2.
34
(MT13 - En 2015)
Internal address (mandatory in case of
multiple devices in the same apartment);
identification address of a device inside the
same apartment (addresses from 0 to 3).
The internal address establishes a hierarchy
in the internal devices since the device with
internal address 0 (zero) will be the main
device and all the other devices will be the
secondary ones. The different internal
address allows you to selectively make and
receive calls between devices within the
same apartment. The external calls or calls
from another apartment will make all devices
ringing, the first device that answers the call
will activate the conversation and switch OFF
the ringer of the other devices. When you
receive a call from an external video door
station, all the devices will ring, but only the
main device (internal address 0 - zero) will
display the camera image. Even from other
video intercom devices in the same
apartment you can monitor the entrance by
pressing the
button; this operation turns
OFF all ringers, turns ON the video intercom
device and simultaneously turns OFF the
main one.
For the coding it is necessary to set the J4 and
J5 jumpers according to the internal address
required (see the following figure). From the
factory the bracket is encoded as standard with
internal address 0 (both jumpers to the right).
Additional programming
After powering up the video intercom system, if
necessary, it is possible to program the
secondary addresses and apply the codes to
be assigned to the “
”, “1” buttons and the
A1 terminal.
Entering codes or addresses
Press button "1", "
" and "
" to enter
addresses or codes.
1 :
Press this button to increase the value
you want to enter. Press the button for a
number of times equal to the digit you want
to enter (digit 1 = 1 time; digit 9 = 9 times;
digit 0 = 10 times).
: Press this button to confirm the digit just
dialled and to proceed to enter next digit
in the following order: hundreds, tens, units.
: Press this button to confirm address or
code programming or go to the next
programming step.
8
7
6
5
4
3
2
1
ON
J4
J5
SW1
J4
J4
J4
J4
J5
J5
J5
J5
0
2
1
3
- Codes and/or addresses must have three
digits (hundreds, tens, units); codes and/or
addresses with tens and units or units only
must be completed by adding zeros. For
example, address 96 will become 096 and
address 5 will become 005.
- Digits must be entered individually (beginning
from the hundred), by pressing the button “1”
for a number of times “n”, where “n” is the
value of the digit you want to enter. Store the
digit pressing the button "
"; a tone will
confirm the acquisition of the 1
st
digit.
- Follow the same procedure to store the 2nd
and 3rd digit.
For example, to enter code 096 you must:
- press button “1” 10 times to enter digit 0 and
press the button “
”; you will hear a tone;
- press button “1” 9 times to enter digit 9 and
press the button “
”; you will hear a tone;
- press button “1” 6 times to enter digit 6 and
press the button “
”; you will hear a tone.
Enter the programming phase
Hold the button
pressed, after 4 sec-
onds you will hear a beep, pick up the hand-
set keeping pressed button
, the pro-
gramming tone will be heard.
Release the button
keeping the handset
OFF hook until the end of programming.
Attention. If for 2 minutes no keys are pressed,
system switches back to the operating mode.
Exit the programming phase
You can exit the programming phase at any
time by replacing the handset.
Programming of the secondary address.
- Secondary user address - By storing the
user address of another apartment it is possible
to receive both the calls (call addressed to its
own videointercom and call addressed to the
other apartment), talk to the external station
and actuate the lock of the external station
calling (i.e.: videointercom installed in common
area for several users, etc.).
To program the secondary user address it is
necessary to:
enter the programming mode following
the instructions described in “Enter the
programming phase”;
keep pressed the button "
" for more than
4 seconds; the programming tone will be
heard;
keep pressed the button "
" for more than
4 seconds; the programming tone will be
heard;
enter the 3 digit of the secondary user
address (code from 001 to 200) following
the procedure reported on the paragraph
“Entering codes or addresses”;
press the button
to confirm; the acknowl-
edge tone will be heard;
proceed with another programming phase
or exit the programming phase by hanging
up the handset.
- Internal secondary address - By
programming the secondary user address
the internal secondary address 000 is
automatically encoded. To change it, please
proceed as follows:
enter the programming mode following
the instructions described in “Enter the
programming phase”;
keep pressed the button "
" for more than
4 seconds; a tone will be heard;
keep pressed the button "
" for more than
4 seconds; a tone will be heard;
keep pressed the button "
" for more than
4 seconds; a tone will be heard;
enter the 3 digit of the internal secondary
address (code from 000 to 003) following
the procedure reported on the paragraph
“Entering codes or addresses”;
press the button
to confirm; the acknowl-
edge tone will be heard;
proceed with another programming or exit
the programming phase by hanging up the
handset.
Programming address to be stored to
button "
"
To this button can be stored the addresses of
maximum 4 external stations which can be
connected sequentially. In this way the user can
monitor, communicate or open the door of 4
different external stations without being called
from them but simply pressing several times
the button
. In the case of a system with
only 1 external door station it isn’t
necessary to store any address because it
will be acquired automatically at the first
call.
To make the programming it necessary to:
enter the programming mode following
the instructions described in “Enter the
programming mode”;
keep pressed the button "
" for more than 4
seconds; a tone will be heard;
enter the 3 digit of the address of the 1st
external door station to be stored (code
from 231 to 250) following the procedure
reported on the paragraph “Entering codes
or addresses”;
press the button
to confirm; the acknowl-
edge tone will be heard;
to enter the address of the 2nd door sta-
tion, press twice the “
” button (each pres-
sure should last about 4 seconds); at each
pressure you will hear a confirmation tone;
enter the 3 digit of the address of the 2nd
door station to be stored (code from 231 to
250) following the procedure reported on the
paragraph “Entering codes or addresses”;
press the button
to confirm; the acknowl-
edge tone will be heard;
if present, and you wish to enter the address
of the 3rd door station, press three times
the “
” button (each pressure should last
about 4 seconds); at each pressure you will
hear a confirmation tone;
enter the 3 digit of the address of the 3rd
door station to be stored (code from 231 to
250) following the procedure reported on the
paragraph “Entering codes or addresses”;
press the button
to confirm; the acknowl-
edge tone will be heard;
if present, and you wish to enter the address
of the 4th door station, press four times the
INTERNAL STATIONS