2.
26
(MT13 - En 2015)
INTERNAL STATIONS
press the button
to confirm the present
address move to the 2nd one; an acknowl-
edge tone will be heard;
enter the 3 digit of the address of the 2nd
external door station and confirm by pressing
button
;
proceed entering the addresses of the 3rd
and 4th external stations (if present) or exit the
present programming phase pressing sev-
eral times the button
, you will be led back
to selecting programming mode;
proceed with another programming or exit
programming mode by pressing button
or
.
Note: store only the addresses of the exter-
nal door stations to which the user can be
connected. Don’t store the addresses of
external door stations belonging to differ-
ent buildings even if in the same installa-
tion.
Buttons 1,2,3,4,5 and 6.
These buttons can be used to:
make intercommunicating calls;
- to call users of different apartments it is
necessary to store in each button of your
monitor the address of the user you wish to
call pressing that button (codes from 001 to
200).
- to call other videointercoms installed in the
same apartment (local intercommu-nicating
service), it is necessary to store in the buttons
1,2,3,4,5,6 of each monitor always the code
000; start from button 1 and go on until you
have programmed, with the code 000, as
many buttons as are the videointercoms
installed in the apartment (max 6 units) you
wish to call; automatically by pressing buttons
1,2,3,4,5 of one unit you will call the unit whose
internal address is related to the pressed
button according to table 2.2.
Internal
Button to press
address
1
2
3
4
5
6
000
001
002 003 004 005 006
001
000
002 003 004 005 006
002
000
001 003 004 005 006
003
000
001 002 004 005 006
004
000
001 002 003 005 006
005
000
001 002 003 004 006
006
000
001 002 003 004 005
Table 2.2.
Addresses for intercommunicating calls
For example if you press the button 3 from the
videointercom whose intercommunicating
address is 002 you will call the
intercommunicating user 003.
monitoring external door stations (it is
suggested to use button
to monitor the
1
st
external door station) to enable this
feature store the address of the external
door station (codes from 231 to 250).
optional functions operated by means
of the actuators art.2281; to enable this
functions store the address of the actuator
to be operated (codes from 211 to 220).
To make the programming it is necessary:
enter the programming mode following
the instructions described in “Enter the
programming mode”;
a - keep pressed for more than 4 seconds
the button you wish to program; red LED
starts flashing;
b -enter the 3 digit of the code of the
desired function following the procedure
reported on the paragraph “Entering
codes or addresses”;
c -press the button
; an acknowledge
tone will be heard and the red LED lights-
ON continuously;
repeat phases a-b-c to program the other
buttons or exit the programming mode
pressing button
or
; red LED turns-
OFF.
Notes.
- In each button can be stored only one code.
- Intercom conversations or connections with
users and external stations of other buildings
will not be possible if digital exchanger
art.2273 is installed.
Programming the number of ringing
call
enter the programming mode following
the instructions described in “Enter the
programming mode”;
a - press button
; only one ring will be
heard;
b - to press left and right the button
to
respectively increase or decrease the num-
ber of rings. After each pressure of the
button the selected number of rings will be
heard;
c - press one of the buttons (1,2,3 or 4) to
select the type of call you wish to change (see
table 2.3);
if it’s required to modify the number of ringing
call of another type of call, repeat points a-b-
c;
proceed with other programming phases or
exit the programming mode pressing the but-
ton
or
; red LED turns-OFF.
Programming a melody for a call type
enter the programming mode following the
instructions described in “Enter the
programming mode”;
a - press the button
; the melody actually
programmed will be heard;
b - to push laterally (left or right side) the
button to select the previous or next ringer
tone;
c - press one of the button 1,2, 3 or 4 to select
the type of call to modify (see table 2.3);
if it is required to modify the melody of another
type of call, repeat the points a-b-c;
exit the programming mode pressing the but-
ton
or
; red LED turns-OFF.
Exit the programming phase
In any situation it is possible to exit the
programming mode by pressing the button
or
.
Example of automatic programming of a user address (code 111)
Table 2.3.
Buttons to programming the type of call
Button
Type of call
1
from external door station
2
from other users
3
intercommunicating
4
floor (local)
