2.
54
(MT13 - En 2015)
INTERNAL STATIONS
monitoring external door stations; to
enable this feature store the address of the
external door station (codes from 231 to
250).
optional functions operated by means
of the actuators art.2281; to enable this
functions store the address of the actuator to
be operated (codes from 211 to 220).
To make the programming it is necessary:
enter the programming mode following
the instructions described in “Enter the
programming phase”;
a - keep pressed for more than 4 seconds
the button you wish to program; yellow LED
starts flashing;
b -enter the 3 digit of the code or address
you wish to store following the procedure
reported on the paragraph “Entering codes
or addresses”;
c -press the button
; an acknowledge
tone will be heard and the yellow LED lights-
ON continuously;
repeat phases a-b-c to program other but-
tons or exit the programming mode by hang-
ing up the handset; yellow LED turns-OFF.
Notes.
- In each button can be stored only one code or
address.
- Intercom conversations or connections with
users and external stations of other buildings
will not be possible if digital exchanger
art.2273 is installed.
Programming the number of ringing call
The intercom can receive 4 different calls that
can be changed as indicated in the procedure
below. The default programming values and
the call sequence are shown in table 2.13.
All programming operations must be carried
out with the handset in idle position.
Keep pressed the button "1" for more than 4
seconds; the yellow LED turns ON and you
hear the ring tone that was programmed for
calls from external door station.
a - Press the button “1” repeatedly to select
the ring tone.
b - Press the button “
” to confirm and go
on to select the number of rings.
c - Press the button “1” as many times as the
desired number of rings (once = 1 ring; 4
times = 4 rings).
d - Press the button “
” to confirm and go
on to program the ring tone for intercom calls.
If you want to change the other two tone rings
(call from other user or floor call), you must
repeat steps a-b-c-d.
Pick up and close the handset for exit the
programming mode; yellow LED turns-OFF.
Adjusting the volume
With the handset in idle position, you can adjust
4 volume levels for all ring tones, as indicated
below:
press the button “1” for 4 seconds; the yellow
LED turns ON and you hear the external door
station ring tone;
hold the button “
” pressed and release it
when you hear the desired volume;
pick up and close the handset for exit the
programming mode; yellow LED turns-OFF.
The volume levels are stored and will be used
for the next calls.
More programming operations for
specific functions
How to program secondary user
addresses
(additional programming operation that does
not depend on the programming operations
of user and internal station addresses)
The following programming operation allows
you to save 4 additional user addresses on the
same intercom (i.e.: exchanger function,
intercom installed in common area with multiple
users, etc.).
N.B.: intercom must be programmed also with
the internal common address as specified in
the following.
To make the programming it is necessary:
enter the programming mode following
the instructions described in “Enter the
programming phase”;
keep pressed the button “
” for more than
4 seconds; yellow LED starts flashing;
again keep pressed the button “
” for
more than 4 sec.; yellow LED starts quickly
flashing;
enter the 3 digit of the 1st user secondary
address (codes from 1 to 200) following the
procedure reported on the paragraph
“Entering codes or addresses”;
press the button "
" to confirm the present
address and move to the 2nd user address;
an acknowledge tone will be heard;
enter the 3 digit of the 2nd user secondary
address and confirm by pressing button
"
";
proceed entering the 3rd and 4th secondary
user addresses consumer (if necessary) or
to press twice the “
” to pass to the inser-
tion of the internal common address;
enter the 3 digit that compose the internal
common address to the 4 new user
addresses (codes from 000 to 006) following
the procedure of the paragraph “Entering
codes or addresses”.
Note: the internal common address has to
be unique and different from you address
him inside eventually programmed on other
intercoms that has the same user address;
to press “
” to confirm and to return of
choice of programming; an acknowledge
tone will be heard and the yellow LED lights-
ON continuously;
pick up the handset for exit the programming
mode.
Note: If you want to make intercom calls, you
must program the call buttons with the codes of
the users you want to call.
Example
How to program three intercoms with user
addresses 101, 102 and 103; from which user
103 should receive also calls addressed to
user 101 and 102; user 101 and 102 should
receive only calls addressed to them.
- User 101 must be programmed only with user
address 101 and internal address 000.
- User 102 must be programmed only with user
address 102 and internal address 000.
- User 103 must be programmed with user
address 103, internal address 000, 1
st
sec-
ondary address 101, 2
nd
secondary address
102, internal common address 001 being the
internal address of intercoms 101 and 102
already programmed to 000.
System programming
The following programming allows you to
personalise the operation mode of button “1”
used to deactivate the ring tones and the GC-
GE terminals and send the floor call to the
systems with the same user address (internal
stations in parallel). See table 2.14.
To make the programming it is necessary:
enter the programming mode following
the instructions described in “Enter the
programming phase”;
keep pressed the button “
” for more than
4 seconds; yellow LED starts flashing;
a - keep pressed the button “1” for more than
4 seconds; yellow LED starts quickly flashing;
b - press the button “2” once to enable
operating mode 0 (you hear a sharp tone);
within 2 seconds press the button “2” again to
disable operating mode 0 (you hear a low
tone);
c - press the button “1” to confirm and pro-
ceed to program the next mode;
you must repeat steps a, b and c to program
all operating modes in table 2.14;
after you have completed the operation and
confirmed operating mode 7 with the button
“1”, press the button “
” and replace the
handset to exit the programming phase.
Note. Programming will not be changed if
the values of all modes are not entered
correctly.
- Programming example of page 2.55.
Resetting the default programming values
To reset the intercom default programming
values and delete all the variations made in the
programming mode you must:
enter the programming mode following
the instructions described in “Enter the pro-
gramming phase”;
press the buttons 6, 5, 4, 3, 2 and 1 succes-
sively; the tone indicates that the default
values have been restored.
Additional functions
See on page 2.43.
Tone and calling tables
See on page 2.44.
