2.
55
(MT13 - En 2015)
2
INTERNAL STATIONS
OPERATION
Call from external station.
When a call is made from the external station,
the intercom generates an acoustic tone and
stays ON for about 30 seconds. Pick up the
handset to start conversation with the external
station for about 90 seconds and press button
"
" to open the door.
Connection with one or more external
stations without receiving the call.
Picking-up the handset when the system in
stand-by and no conversation in progress you
will hear the tone of system ready.
By pressing the button "
" you will be
connected with the door station or, if more than
one door station is present in the system, with
the door station from which you received the
last call; in this case if the buttons from 1 to 6
have been programmed with the addresses of
the door stations present in the system it would
be possible to communicate with them by
pressing the associated buttons.
If picking up the handset you did not get any
tone, the system is busy (a communication with
another user is in progress), and no other
operations are allowed until the system
becomes free.
Making or receiving a call from another
user.
When the installation is in stand-by, you can
make a call to another user. You must have
stored the address of the desired user’s in the
buttons 1÷6.
To make the call, pick up the handset, wait for
the free tone and press button. You will hear the
call tone and the intercom of the called
user will ring with a ring different from
calls from external stations or intercom
calls from the same apartment. If the
called user answers within 30 seconds, a
90-second conversation starts, otherwise
the system goes back to free.
The internal conversation in progress will
be automatically interrupted in case of
call from external station to any other
user.
If you pick up the handset and receive no
tone, the installation is busy and you must
wait until it is free.
Making or receiving an intercom call
in your apartment.
When the installation is in stand-by, you
can make an intercom call to all intercom
in the same apartment (max 7 with internal
address from 000 to 006) by pressing
buttons previously programmed with code
000 (see table 2.15).
To make the intercom call, pick up the
handset, wait for the free tone and press
proper button. After pressing the button
you will get a calling tone on the
loudspeaker, while the intercom of the
called user rings with the programmed
melody. If the called user answers within
30 seconds, a 90-second conversation
starts, otherwise the system goes back
to free.
The internal conversation in progress will
be automatically interrupted in case of
call from external station to any other
user.
Calling
Intercom to call
intercoms CT0 CT1 CT2 CT3 CT4 CT5 CT6
CT0 (000)
-
CT1 (001)
-
CT2 (002)
-
CT3 (003)
-
CT4 (004)
-
CT5 (005)
-
CT6 (006)
-
Button to press
(all programmed with code 000)
N.B.: The codes in parenthesis in the table are the
identification addresses of the internal stations that
were programmed previously (see chapter
“programming of the user address and internal
address”).
Examples:
- From intercom CT1 (internal address 001) press
the button 1 for calls to intercom CT0.
- From intercom CT2 (internal address 002) press
the button 4 for calls to intercom CT4.
- From intercom CT4 (internal address 004) press
the button 4 for calls to intercom CT3.
Table 2.15. Button use for intercom calls of max.
7 intercoms in the same apartment.
Table 2.14 - System programming codes
Default
To enable
To disable
Operating modes
value
press 1 time
press 2 times
button "2"
button "2"
mode 0
send floor call to other internal stations in parallel (1)
disabled
enabled
disabled
mode 1
button “1” deactivates all ring tones (2)
disabled
enabled
disabled
mode 2
button “1” deactivates all ring tones and button tones (2)
disabled
enabled
disabled
mode 3
button “1” does not deactivate ring tones and button tones (2)
disabled
enabled
disabled
mode 4
reserved; disabled
disabled
-
disabled
mode 5
the GC-GE terminals are activated upon call from external door station (3) disabled
enabled
disabled
mode 6
the GC-GE terminals are activated upon intercom call (3)
disabled
enabled
disabled
mode 7
reserved; disabled
disabled
-
disabled
(1) From the internal station connected to the floor call button (terminal A1) and with operating mode 0 enabled, the floor call is also sent to the
other apparatuses in parallel.
(2) If modes 1, 2 and 3 are disabled, press the button “1” for 4 seconds , without a conversation in progress, to deactivate the external and intercom
ring tones. To reactivate the ring tones, press the button “1” again for 4 seconds; you hear the confirmation tone.
(3) If modes 5 and 6 are disabled, the GC and GE terminals are activated to send the calls.
Example of system programming to enable operating mode 0 and 2 and to disable all the others operating modes
