background image

  

Description

DESCRIPTION

Ambie

nt a

nd 

Op

erating

 Co

nditio

ns

1.

Ref.2003

· 37 ·

QC-PDS

HARDWARE

1.6

Ambient and Operating Conditions

Terms

Regulation

Test reference

Mechanical specifications

Shipping

Vibration

Meets:
IEC 60721-3-2

Class 2M1, sinusoidal vibration

2 Hz 



 

9 Hz, 3.5 mm amplitude

9 Hz 



 200 Hz, 1 g

200 Hz 



 500 Hz, 1.5 g

Jerk limit

Meets:
IEC 60721-3-2 
IEC 61800-2

Class 2M1, 
packed unit

Operation

Ambient sinusoidal 
vibration tests

Meets:
CEI 60068-2-6, 
Fc test

Sinusoidal vibration

10 Hz 



 57 Hz,

constant 0.075 mm amplitude
57 Hz 



 150 Hz, 

1 g constant acceleration

Degrees of sealing 
protection
(code IP)

Meets:
EN 60529

Open IP xx.

**

 

Always install inside 
an electrical cabinet

Ambient conditions

Storage *

Ambient 
temperature

Meets:
IEC 60721-3-1 
IEC 61800-2

1K4, 
From -25 ºC to +60 ºC

Shipping *

Damp heat test 
(stationary state)

Meets:
IEC 60068-2-78 
IEC 61800-5-1

Disconnected power supply
40ºC +/-2ºC and 
93 % +2-3 % without condensation

Ambient 
temperature

Meets:

IEC 60068-2-1
IEC 61800-2

Packed
unit 
-40 °C to +70 ºC

Operation

Ambient test. 
Cold

Meets:
CEI 61800-2

5 ºC in running 
conditions

Ambient test. 
Dry heat

Meets: 
IEC 60068-2-2, 
Bd test

Under nominal conditions of 45 °C.

Under running conditions between

5 ºC and 55 ºC with derating (see

derating characteristic).

Damp heat test 
(stationary state)

Meets: 
IEC 60068-2-78 
IEC 61800-5-1

Disconnected power supply. 40 ºC
+/-2 ºC 
93 % +2-3 % non-condensing

Installation altitude 

over average 

sea level without 

derating

Meets: 
IEC 61800-5-1 
IEC 60664-1

Pollution degree 2 

and altitude of 

  2000 amsl under 

nominal conditions

*

The shipping and storage environment must be dry and dust free.

**

Open IP xx

, to be installed inside a cabinet or assembly that provides the required access

protection.

Summary of Contents for QC-PDS





































































































































































































































































































































































































































Reviews: