C4000I
36
532100 - Rev.A
Tr
ansla
tion of the original instruc
tions
ENGLISH
!
Ensure that there are no obstacles (persons or things)
while the automation is moving.
SLH/SLH LR - MEMORISING THE FIRST RADIO
CONTROL
1. Press and hold down the + button (OPEN A
programming) or - (OPEN B/CLOSE program-
ming). After pressing the button for about 5
seconds, the corresponding radio LED (DL4 or DL5)
will start to flash to indicate that the radio code
learning phase has started.
2. Release the button. The E4000I now remains in
the learning phase for approximately 20 seconds.
3. Press and hold down buttons P1 and P2 simulta-
neously on the SLH/SLH LR radio control (master
version only). The LED on the radio control starts
to flash.
4. Release both buttons; the LED on the radio control
continues to flash.
5. Make sure that the LED DL4 or DL5 on the board is
still flashing and press the button of the radio con-
trol that you wish to memorise for a few seconds
(the LED becomes steady). Release the button of
the radio control.
6. Press the same button that was used in the pre-
vious step twice in succession to complete the
memorisation process. If the procedure was
carried out correctly, the C4000I will open the
gate, if permitted by the operating mode that
has been set.
SLH/SLH LR - MEMORISING OTHER RADIO
CONTROLS
1. Press and hold down buttons P1 and P2 simul-
taneously on the SLH/SLH LR radio control that
has already been memorised (master version
only). The LED on the radio control starts to flash.
2. Release both buttons; the LED on the radio control
continues to flash.
3. Press and hold down the button that has already
been memorised (the LED becomes steady).
4. Place the remote control that has already been
memorised close to the remote control to be
memorised (keeping the button in the previous
step pressed).
5. Press the button of the radio control to be mem-
orised and make sure that its LED flashes twice,
to indicate that the procedure was completed
successfully, before turning off.
6. Release all buttons.
7. Press the button used in step 5 twice in succession
to complete the memorisation process for the new
radio control. If the procedure was carried out
correctly, the C4000I will open the gate, if per-
mitted by the operating mode that has been set.
LC/RC - MEMORISING THE FIRST RADIO
CONTROL
1. Press and hold down the + button (OPEN A
programming) or - (OPEN B/CLOSE program-
ming). After pressing the button for about 5
seconds, the corresponding radio LED (DL4 or DL5)
will start to flash to indicate that the radio code
learning phase has started.
2. Release the button; the E4000I now remains in the
learning phase for approximately 20 seconds.
3. Make sure that the LED DL4 or DL5 on the board is
still flashing and press the button of the LC/RC
radio control that you wish to memorise for a few
seconds (the LED becomes steady). The corre-
sponding LED (DL4 or DL5) on the board will light
up with a steady light for 1 second and will then
start to flash again for another 20 seconds, during
which another radio control can be memorised.
4. To memorise additional radio controls at a later
stage, repeat the procedure from the beginning
or carry out the remote memorisation procedure.
LC/RC - REMOTE CODE MEMORISATION
PROCEDURE
Additional radio controls can be memorised remotely,
i.e. without having to use the board directly, by using a
radio control that has already been memorised.
1. When close to the E4000I, press and hold down
buttons P1 and P2 simultaneously on the radio
control that has already been memorised (as OPEN
A or OPEN B/CLOSE). The LED of the radio control
and the LED, DL4 or DL5, of the board will start to
flash for 5 seconds.
2. Release both buttons and then press the button
that has already been memorised within 5 sec-
onds. The E4000I now remains in the learning
phase for approximately 20 seconds.
3. Make sure that the LED DL4 or DL5 on the board
is still flashing and press the button of the radio
control that you wish to memorise. The corre-
sponding LED (DL4 or DL5) on the board will turn
on with a steady light for 2 seconds and will then
start to flash again for another 20 seconds, during
which another radio control can be memorised.
4. Wait for LED DL4 or DL5 on the board to turn off
before using the new radio control.
DS - MEMORISING RADIO CONTROLS
1. Set the required ON/OFF combination of the 12 DIP
switches on the DS radio control. Avoid setting all
of them to ON or all of them to OFF.
2. Press and hold down the + button (OPEN A
programming) or - (OPEN B/CLOSE program-
ming). After pressing the button for about 5
seconds, the corresponding radio LED (DL4 or DL5)
will start to flash to indicate that the radio code
