C4000I
32
532100 - Rev.A
Tr
ansla
tion of the original instruc
tions
ENGLISH
Advanced function
Default
o1
OUT 1
Allows output OUT1 (NO open collector) to be set
in one of the following functions:
00
always
active
01
Fail
safe
02
indicator lamp (off = closed; on = opening
and when open/paused; flashing = closing)
03
courtesy light (remains on for the duration
of the movement in addition to the time set in t1)
04
active
error
05
gate open or paused
06
gate
closed
07
gate
moving
09
gate
opening
10
gate
closing
12
safety device active
13
traffic light function (active during opening
and with gate open)
14
timed output that can be activated by the
second radio channel OMNIDEC (see function t1)
15
output that can be activated by the second
radio channel OMNIDEC (step-by-step function)
19
battery
operation
02
t1
OUT 1 TIMING (displayed only with function
o1
=
03
or
o1
=
14
)
Can be used to adjust the timing of output OUT1 if a
timed function was selected, from 1 to 59 minutes
in 1 minute steps.
02
AS
MAINTENANCE REQUEST - CYCLE COUNTER (linked
to the next two functions)
Allows you to enable a maintenance alert (sched-
uled maintenance) or the cycle counter.
Y
enables the alert when the programmed
number of cycles had been reached (as defined in
the next two functions).
The alert consists of a pre-flashing of 8 sec (in
addition to any pre-flashing time that may have
already been set) before each movement.
no
enables the cycle counter, that will be dis-
played in the next two functions up to the maximum
displayable 99,990.
If the number of cycles carried out is greater than
99,990 the next two functions
nc
and
nd
will
display
99
and
99
respectively.
no
Advanced function
Default
nc
CYCLE PROGRAMMING (THOUSANDS)
If
AS
=
Y
the display will indicate the number of
thousands of cycles after which the maintenance
alert starts (can be set from
0
to
99
).
If
AS
=
no
the display will indicate the number of
thousands of cycles performed. The value displayed
is updated as the cycles progress, interacting with
the value in
nd
.
If
AS
=
no
the cycle counter can be reset by: press
+ and - for 5 sec.
00
nd
CYCLE PROGRAMMING (TENS)
If
AS
=
Y
the display will indicate the number of
tens of cycles performed, after which the mainte-
nance alert starts (can be set from
0
to
99
).
If
AS
=
no
the display will indicate the number
of tens of cycles performed. The value displayed is
updated as the cycles progress, interacting with
the value of nc.
E.g. If the system has performed 11,218 cycles,
nc
=
11
and
nd
=
21
will be displayed.
00
SL
SLEEP
Allows the energy saving function to be ena-
bled. After 10 minutes of inactivity the board
goes into low power mode: the safety devices, BUS
devices and all the relative LEDS are de-energised.
The display indicates status
13
until the device is
activated.
Y
enabled
no
not
enabled
no
Hr
FORCED COMMANDS
Y
the maintained OPEN B command causes
the gate to open like FORCED OPENING. The
maintained STOP command causes the gate to close
like FORCED CLOSING.
no
not
enabled
!
Activating forced commands:
- disables operations such as OPEN
B and STOP.
- must be intentional and the gate
visible.
- it has priority over the operation
of the SAFE OP and SAFE CL safety
devices.
- it cannot be used via radio devices
and BUS 2easy.
no
St
AUTOMATED SYSTEM STATUS
See
St
Basic Function
Y
