manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from manualshive.com.

Share
Download
background image

 

1384

ExtremeWare 7.5 Command Reference Guide

Wireless Commands

[3] Jul 26 17:14:56 :2 WEP Encryption Mode set to 128-BIT Encryption

[3] Jul 26 17:14:56 :1 WEP Encryption Mode set to 128-BIT Encryption

[3] Jul 26 17:14:56 :2 Web netlogin mode disabled

[3] Jul 26 17:14:56 :1 Web netlogin mode disabled

[3] Jan 01 00:00:12 :2 Authentication state time updated to 600

[3] Jan 01 00:00:12 :2 Association state time updated to 600

[3] Jan 01 00:00:12 :1 Authentication state time updated to 600

[3] Jan 01 00:00:12 :1 Association state time updated to 600

[3] Jan 01 00:00:12 :2 Max association clients updated to 100

[3] Jan 01 00:00:11 :1 Max association clients updated to 100

[3] Jan 01 00:00:11 :2 Long Retry Limit updated to 7

[3] Jan 01 00:00:11 :1 Long Retry Limit updated to 7

[3] Jan 01 00:00:11 :2 Short Retry Limit updated to 4

[3] Jan 01 00:00:11 :1 Short Retry Limit updated to 4

[3] Jan 01 00:00:11 :1 Preamble mode set to SHORT

[3] Jan 01 00:00:10 :2 RTS Length updated to 2330

[3] Jan 01 00:00:10 :1 RTS Length updated to 200

[3] Jan 01 00:00:10 :2 Fragmentation Threshold updated to 2345

[3] Jan 01 00:00:10 :1 Fragmentation Threshold updated to 1200

[3] Jan 01 00:00:10 :2 Beacon Interval updated to 40

[3] Jan 01 00:00:10 :1 Beacon Interval updated to 40

[3] Jan 01 00:00:00 Wireless Port Up

[3] Jan 01 00:00:00 Boot reason: Power-on Boot

S300-24-FZ:37 #

History

This command was first available in ExtremeWare 6.2a and added to the “

e

” series in 7.3e.

Platform Availability

This command is available on the Summit 300-48, Summit 300-24, Summit 400-24p and Alpine switches.

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

F-SECURE PSB Getting Started Manual preview
PSB
Brand: F-SECURE Pages: 18
Samsung UN40C7000WF User Manual preview
UN40C7000WF
Brand: Samsung Pages: 7
Crestron CRESTRON-APP-SSTV Operations & Installation Manual preview
CRESTRON-APP-SSTV
Brand: Crestron Pages: 28
Omron CX-SUPERVISOR V3 Brochure preview
CX-SUPERVISOR V3
Brand: Omron Pages: 5
AMX Content Database Editor v 1.0 Manual preview
Content Database Editor v 1.0
Brand: AMX Pages: 28
GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Installation & Programming Instructions preview
GARDTEC SPEECH DIALLER
Brand: GARDINER TECHNOLOGY Pages: 38
Lexmark LexPrint User Manual preview
LexPrint
Brand: Lexmark Pages: 20
3Com SUPERSTACK II HUB 10 24-PORT TP User Manual preview
SUPERSTACK II HUB 10 24-PORT TP
Brand: 3Com Pages: 8
3Com 3CWXMUPA Release Note preview
3CWXMUPA
Brand: 3Com Pages: 8
Kinoma CLIE PEG-TJ27 Quick Start Manual preview
CLIE PEG-TJ27
Brand: Kinoma Pages: 6
Intrinsyc Telephony Modem Simulator Brochure preview
Telephony Modem Simulator
Brand: Intrinsyc Pages: 2
Red Hat CERTIFICATE SYSTEM 8 - AGENTS GUIDE Agents Manual preview
CERTIFICATE SYSTEM 8 - AGENTS GUIDE
Brand: Red Hat Pages: 146
DeLorme XMap 7 GIS Getting Started Manual preview
XMap 7 GIS
Brand: DeLorme Pages: 29
DeLorme XMap 6 User Manual preview
XMap 6
Brand: DeLorme Pages: 437
Intel Rapid Storage Technology User Manual preview
Rapid Storage Technology
Brand: Intel Pages: 19
GRASS VALLEY AURORA INGEST 7 Datasheet preview
AURORA INGEST 7
Brand: GRASS VALLEY Pages: 4
GRASS VALLEY Aurora Browse Upgrade Instructions preview
Aurora Browse
Brand: GRASS VALLEY Pages: 42
Autodesk 00128-051462-9310 - AUTOCAD 2008 COMM UPG FRM 2005 DVD User Manual preview
00128-051462-9310 - AUTOCAD 2008 COMM UPG FRM 2005 DVD
Brand: Autodesk Pages: 2268

Brands by name

Popular brands

Load more brands