manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from manualshive.com.

Share
Download
background image

 

configure debug-trace wireless

ExtremeWare 7.5 Command Reference Guide

1195

configure debug-trace wireless

configure debug-trace wireless ports [<portlist> | all] [dot1x | radius | 

mac | snmp | wlan-driver | eth-driver | ap-scan | client-diag | mac-radius 

| wpa-wpa2 | iapp] <debug-level>

Description

Enables debug tracing for troubleshooting.

Syntax Description

Default

Disabled

Usage Guidelines

Use to trace messages for troubleshooting.

Example

The following example enables debug tracing for IAPP on port 1:15 with a debug level of 2:

configure debug-trace wireless ports 1:15 iapp 2

History

This command was first available in ExtremeWare 7.3e.

portlist

Specifies one or more ports or slots and ports. Can be one or more port numbers. May be in the 
form 1, 2, 1:2, 3-5, 2:*, 2:5, 2:6-2:8.

all

Specifies all ports.

dot1x

Configures debug tracing level for the 802.1x activity.

radius

Configures debug tracing level for the RADIUS activity.

mac

Configures debug tracing level for the MAC layer activity.

snmp

Configures debug tracing level for the SNMP activity.

wlan-driver

Configures debug tracing level for the WLAN driver activity.

eth-drive

Configures debug tracing level for the Ethernet driver activity.

ap-scan

Configures debug tracing level for the Access Point Scans.

client-diag

Configures debug tracing level for the Client Diagnostics.

mac-radius

Configures debug tracing level for the MAC-RADIUS activity.

wpa-wpa2

Configures debug tracing level for the WPA and WPA2 activities.

iapp

Configures debug tracing level for the IAPP activity.

debug-level

Specifies a debug level. The default is 0 (off).

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

F-SECURE ANTI-VIRUS FOR MIMESWEEPER - Administrator'S Manual preview
ANTI-VIRUS FOR MIMESWEEPER -
Brand: F-SECURE Pages: 44
ShoreTel ShoreWare User Manual preview
ShoreWare
Brand: ShoreTel Pages: 25
Citrix MetaFrame MetaFrame Presentation Server Reviewer'S Manual preview
MetaFrame MetaFrame Presentation Server
Brand: Citrix Pages: 97
Crestron SIMPL Windows Installation & Operating Manual preview
SIMPL Windows
Brand: Crestron Pages: 230
Canon DV Messenger 2 Instruction Manual preview
DV Messenger 2
Brand: Canon Pages: 40
Canon SELPHY CP400 User Manual preview
SELPHY CP400
Brand: Canon Pages: 97
Canon ScanGear CS-S 4.3 User Manual preview
ScanGear CS-S 4.3
Brand: Canon Pages: 109
Canon CanoScan FS2700F User Manual preview
CanoScan FS2700F
Brand: Canon Pages: 80
Canon Digital Video Software (Windows) Instruction Manual preview
Digital Video Software (Windows)
Brand: Canon Pages: 89
Canon CameraWindow Instruction Manual preview
CameraWindow
Brand: Canon Pages: 98
Canon Cloud Portal User Manual preview
Cloud Portal
Brand: Canon Pages: 88
Canon UFR II Driver Manual preview
UFR II
Brand: Canon Pages: 168
Canon Digital Camera Solution Disk V.27 Software & Wireless Manual preview
Digital Camera Solution Disk V.27
Brand: Canon Pages: 130
Canon Viewer for Pocket PC RV-P1.0 User Manual preview
Viewer for Pocket PC RV-P1.0
Brand: Canon Pages: 22
Canon S 530D Brochure & Specs preview
S 530D
Brand: Canon Pages: 2
Canon S830D - S Color Inkjet Printer User Manual preview
S830D - S Color Inkjet Printer
Brand: Canon Pages: 201
Canon WEBVIEW LIVESCOPE 3.2 User Manual preview
WEBVIEW LIVESCOPE 3.2
Brand: Canon Pages: 56
Canon WebView Livescope MV Ver. 2.1 LE User Manual preview
WebView Livescope MV Ver. 2.1 LE
Brand: Canon Pages: 24

Brands by name

Popular brands

Load more brands