esera automation 1-Wire Controller 2 Programming Manual Download | Manualshive

Page: 2 / 77

background image

All rights reserved. Reproduction as well as electronic duplication of this guide, complete or in part, requires the written consent of ESERA-
Automation or E-Service GmbH. Errors and technical modification subject to change.

©

ESERA-Automation, E-Service GmbH 2019

www.esera.de

Programming Manual Controller-Gateway-Station V1.0 R1.1

Page 2 of 77

1.

ESERA Concept of Automation

1.1.

1-Wire Controller and 1-Wire Gateway

Sensors and actuators of the 1-Wire bus system are automatically detected, integrated and queried at very high
speed via the 1-Wire Controller / 1-Wire Gateway. The sensor and actuator data are transmitted to your controller
via Ethernet interface, via ASCII (1-Wire Controller) or via ASCII and Modbus protocol. The 1-Wire Controller and
1-Wire Gateway devices are compatible with all controllers within the Smart Home and Smart Automation area.

The 1-Wire controllers are widely used in private and semi-professional environments. Due to the Modbus
RTU and Modbus TCP interface, the 1-Wire Gateway devices are preferred in the demanding Smart Home
and professional automation area.

Core functions of the 1-Wire Controller / 1-Wire Gateway concept

•

Independent recognition and management of sensors and actuators

•

Fast cyclic data-retrieval of sensors and actuators

•

Plausibility check of sensor data

•

Data conversion for standard sensors and ESERA-Automation sensors as well as actuators through
integrated formula collection

•

Data output in ASCII text and Modbus protocol (1-Wire Gateway only)

•

Cyclic life signs (heartbeat) among controller / central control unit and 1-Wire Controller / 1-Wire
Gateway

«
1
2
3
4
...
»

Summary of Contents for 1-Wire Controller 2














































































Reviews:

No comments

Related manuals for 1-Wire Controller 2

Brand: Daikin Pages: 8

Brand: Daikin Pages: 16

DCF-650W - Air Wireless CompactFlash Cf 802.11B...

Brand: D-Link Pages: 28

Brand: Hama Pages: 12

Brand: Tektronix Pages: 2

Brand: Elnec Pages: 2

Brand: Intermec Pages: 102

Brand: Manhattan Pages: 2

Brand: Aiphone Pages: 2

Brand: Daikin Pages: 20

Brand: Greenlee Pages: 36

Brand: StarTech.com Pages: 10

AirStation WLI-USB-KB11

Brand: Buffalo Pages: 45

1130U2 - Storage Controller RAID)- U2W SCSI 80 MBps

Brand: Adaptec Pages: 82

Brand: 3idee Pages: 7

Redbooks ServeRAID-3HB

Brand: IBM Pages: 20

PEPWAVE MAX Adapter

Brand: peplink Pages: 20

Brand: Hama Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands