esera automation 1-Wire Controller 2 Programming Manual Download

Page: 4 / 77

All rights reserved. Reproduction as well as electronic duplication of this guide, complete or in part, requires the written consent of ESERA-
Automation or E-Service GmbH. Errors and technical modification subject to change.

ESERA-Automation, E-Service GmbH 2019

www.esera.de

Programming Manual Controller-Gateway-Station V1.0 R1.1

Page 4 of 77

ESERA Station-200 is a combination of 1-Wire Gateway and embedded computer

•

The 1-Wire Gateway System is based on a

standardized bus system

that has been successfully used

in industrial environments for many years.

•

Open bus-system,

compatible with sensors and actuators of third-party manufacturers

•

Data preparation

and output in a format readable by many controllers (ASCII characters) or Modbus*

protocol

Core functions of the 1-Wire Controller / 1-Wire Gateway concept

•

Independent recognition and management of sensors and actuators

•

Fast cyclic data-retrieval of sensors and actuators

•

Plausibility check of sensor data

•

Data conversion for standard sensors and ESERA-Automation sensors as well as actuators through
integrated formula collection

•

Data output in ASCII text and Modbus protocol (1-Wire Gateway only)

•

Cyclic life signs (heartbeat) among controller / central control unit and 1-Wire Controller / 1-Wire
Gateway

* 1-Wire Gateway devices only

Summary of Contents for 1-Wire Controller 2














































































Search results

Summary of Contents for 1-Wire Controller 2

Reviews:

Related manuals for 1-Wire Controller 2

Brands by name

Popular brands

esera automation 1-Wire Controller 2, Programming Manual

Search results

Summary of Contents for 1-Wire Controller 2

Reviews:

Related manuals for 1-Wire Controller 2

Brands by name

Popular brands