esera automation 1-Wire Controller 2 Programming Manual Download | Manualshive

Page: 76 / 77

background image

All rights reserved. Reproduction as well as electronic duplication of this guide, complete or in part, requires the written consent of ESERA-
Automation or E-Service GmbH. Errors and technical modification subject to change.

©

ESERA-Automation, E-Service GmbH 2019

www.esera.de

Programming Manual Controller-Gateway-Station V1.0 R1.1

Page 76 of 77

26.

Error list of all OWDs

Hier werden als Liste die Error Counter für alle 30 OWDs (1-Wire Bausteine) des 1-Wire Controller / 1-Wire
Gateways ausgegeben.
Wenn es beim Lesen eines OWD einen Fehler gibt, wird der OWD Error Counter um einen Zählerwert erhöht.
Der maximale Error Counter Wert beträgt 65000.
Der Error Counter wird jeweils um Mitternacht (0 Uhr) zurückgesetzt.

Befehl: GET,OWB,ERRLIST1

Beispiel:
1_ERR|18:47:48
1_ERROWD1|255
1_ERROWD2|255
…
1_ERROWD30|255

Error counters for all 30 OWDs (1-Wire devices) of the 1-Wire Controller / 1-Wire Gateway are output here in list
format.
If an error occurs while reading an OWD, the OWD error counter is increased by one counter value. The
maximum error counter value is 65000.
The error counter is reset at midnight (0 o'clock).

Command: GET,OWB,ERRLIST1

Example:
1_ERR|18:47:48
1_ERROWD1|255
1_ERROWD2|255
…
1_ERROWD30|255

«
...
74
75
76
77
»

Summary of Contents for 1-Wire Controller 2














































































Reviews:

No comments

Related manuals for 1-Wire Controller 2

Brand: National Instruments Pages: 4

Brand: National Instruments Pages: 20

Brand: ICON Pages: 6

Carlyle Tools 791-7136

Brand: Napa Pages: 13

Brand: Dawicontrol Pages: 32

Brand: National Instruments Pages: 6

Brand: IOGear Pages: 60

Brand: MSI Pages: 82

Brand: Dell Pages: 49

EtherExpress Pro/10+

Brand: Dell Pages: 16

Brand: Dell Pages: 17

Brand: Dell Pages: 11

Brand: Dell Pages: 101

Brand: Dell Pages: 10

Latitude E6400 XFR

Brand: Dell Pages: 74

TrueMobile 1300

Brand: Dell Pages: 142

Latitude E6400 XFR

Brand: Dell Pages: 81

PowerVault MD3000

Brand: Dell Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands