esera automation 1-Wire Controller 2 Programming Manual Download | Manualshive

Page: 30 / 77

background image

All rights reserved. Reproduction as well as electronic duplication of this guide, complete or in part, requires the written consent of ESERA-
Automation or E-Service GmbH. Errors and technical modification subject to change.

©

ESERA-Automation, E-Service GmbH 2019

www.esera.de

Programming Manual Controller-Gateway-Station V1.0 R1.1

Page 30 of 77

Settings and 1-Wire devices

By command (SET,SYS,SAVE) all settings of the 1-Wire Controller / 1-Wire Gateway and all
1-Wire devices and modules (SET,OWB,SAVE) can be stored permanently. If these settings are not saved, the 1-
Wire Controller / 1-Wire Gateway will start after a reset or a power interruption with the previous basic settings
and possibly different device sequence.

a. All 1-Wire sensors and actuators can be conveniently managed via the Config-Tool.
b. For many ESERA sensors and actuators, formulas are available within the 1-Wire Controller / 1-Wire

gateways. These formulas can be selected via a drop-down list and assigned to a sensor or actuator.

Reset device to factory settings

The 1-Wire Controller / 1-Wire Gateway can be reset to the factory settings via the push button "LOAD FACTORY
DEFAULT". This also deletes all settings for the 1-Wire devices (OWD).
After loading the factory settings, a reset and a restart will be triggered automatically.
The previous settings are overwritten by the default settings.
Alternatively, only the settings of the 1-Wire Controller / 1-Wire Gateway can be reset.

b. Formula selection for ESERA

sensors and actuators

b. Overview sensors and actuators with

serial number, status, article number
and name

All factory settings
(default)

Factory settings

setting only

«
...
28
29
30
31
32
...
»

Summary of Contents for 1-Wire Controller 2














































































Reviews:

No comments

Related manuals for 1-Wire Controller 2

Brand: Garmin Pages: 4

Brand: Tamio Pages: 2

Brand: AR Pages: 20

Powerline PL1200

Brand: NETGEAR Pages: 12

Brand: Audio Partnership Pages: 46

Brand: National Instruments Pages: 6

Brand: Lindy Pages: 2

Brand: AR Pages: 22

Brand: BeeWi Pages: 73

Brand: Dynex Pages: 23

Brand: l-com Pages: 54

Brand: ST-Lab Pages: 4

Brand: TP-Link Pages: 2

73-30130-01261-5

Brand: Kvaser Pages: 25

WebLogic Server

Brand: BEA Pages: 294

Brand: IBM Pages: 11

Brand: Neo Car Audio Pages: 2

LIFESAVER LIFWMB2

Brand: PSA Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands