Epson VT Series Manipulator Manual Download Page 203

Page: 203 / 274

Maintenance 11. Joint #3

VT Rev.1

187

Joint #3 Motor

Removal

(1) Turn ON the Manipulator.

(2) Release the Joint #3 brake. Tilt the Arm #3 and push it against the Arm #2.

The Arm #3 falls by its weight when the Joint #3 motor unit is removed. Therefore,

release the brake and tilt the Arm #3 in advance.

EPSON

RC+

Command

>brake off, 3

When pushing the arm, push the Arm #3 slowly to the Arm #2.

If a strong impact is applied to the joint, the Manipulator may get damage.

(3) Turn OFF the Manipulator.

(4)

Remove the Arm #2 cover.

Reference:

Maintenance 7.2 Arm #2 Cover

(5) Cut off the wire tie bound inside the Arm #2.

Wire tie

: AB150

AB100

Be careful not to cut the harness.

Wire ties

(6) Remove the cable fixing plate on the Arm #2.

(Joint #3 side)

Hexagon socket head cap bolts with captive

washer: 4-M4

(7) Loosen the mounting screws of the Joint #3 motor

unit and remove the Joint #3 timing belt.

Hexagon socket head cap bolts: 3-M4

(with slotted hole washer)

(8) Remove the Arm #2 from the motor unit.

Hexagon socket head cap bolts: 3-M4

(with slotted hole washer)

(9) Disconnect the following connectors from the AMP board.

A: Power cable connector

B: Brake connector

C: Signal cable connector (for AMP board)

D: Motor connector



NOTE



NOTE

Summary of Contents for VT Series


















































































































































































































































































Search results

Summary of Contents for VT Series

Reviews:

Related manuals for VT Series

Brands by name

Popular brands

Epson VT Series, Manipulator Manual

Search results

Summary of Contents for VT Series

Reviews:

Related manuals for VT Series

Brands by name

Popular brands