manualshive.com logo in svg

Epson R320 - Stylus Photo Color Inkjet Printer, Service Manual

The Epson R320 - Stylus Photo Color Inkjet Printer is a high-quality printing solution that delivers stunning photo prints. With its advanced specifications and user-friendly features, this printer allows you to produce professional-quality prints from the comfort of your home. For easy and hassle-free setup, download the free user manual from our website.

Share
Download
background image

EPSON Stylus Photo R320

Revision B

DISASSEMBLY AND ASSEMBLY

Overview

32

2.1  Overview

This section describes procedures for disassembling the main components of Stylus 
Photo R320. Unless otherwise specified, disassembled units or components can be 
reassembled by reversing the disassembly procedure. 

"WARNING" indicates procedures which may result in damage, injury or involving 
human lives if you don't take extra care.
"CAUTION" indicates precautions for any disassembly or assembly procedures.
"CHECK POINT" indicates points to be checked. 
"REASSEMBLY" indicates reassembling procedures which are different from the 
reverse order of the disassembling.
"ADJUSTMENT REQUIRED" indicates required adjustments after the assembly and 
the disassembly.

Read precautions described in the next section before starting.

2.1.1  Precautions

Before starting the disassembling/reassembling work of this product, the following  
"WARNING" and "CAUTION" should always be observed carefully.

W A R N I N G

„

Disconnect the power cable before disassembling or assembling 
the printer.

„

If you need to work on the printer with power applied, strictly 
follow the instructions in this manual.

„

Wear protective goggles to protect your eyes from ink. If ink gets 
in your eye, flush the eye with fresh water and see a doctor 
immediately.

„

Always wear gloves for disassembly and reassembly to avoid 
injury from sharp metal edges.

„

To protect sensitive microprocessors and circuitry, use static 
discharge equipment, such as anti-static wrist straps, when 
accessing internal components.

„

Never touch the ink or wasted ink with bare hands. If ink comes 
into contact with your skin, wash it off with soap and water 
immediately. If you have a skin irritation, consult a physician.

„

When reassembling the waste ink pads and tray, always make 
sure that the waste ink tube is fitted correctly in the specified 
place. Fitting the ink tube in other than the specified position 
could cause ink leakage.

W A R N I N G

„

Avant de commencer, assure vous que l’imprimante soit eteinte 
et que le cordon d’alimentation soit debranche.

„

Veillez a jeter les piles usagees selon le reglement local.

C A U T I O N

Risque d’explosion si la pile est remplacée incorrectment. Ne 
remplacer que par une pile du même type ou d’un type équivalent 
recommandé par le fabricant. Eliminer les piles déchargées selon 
les lois et les règles de sécurité en vigueur.

C A U T I O N

„

When transporting the printer after installing the ink cartridge, 
be sure to pack the printer without removing the ink cartridge 
and secure the cartridge to the main body with adhesive tape.

„

Use only recommended tools for disassembling, assembling or 
adjusting the printer. (Refer to Table 2-1 "Tool List".)

„

Observe the specified torque when tightening screws.

„

Use the specified lubricants and adhesives. (Refer to Chapter 4 
for details.)

„

Make the specified adjustments when you disassemble the 
printer. (Refer to Chapter 3 for details.)

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer



















































































































Reviews:

No comments

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Panasonic Section 700 Operation preview
Section 700
Brand: Panasonic Pages: 289
Samsung ML-2240 - 23 Ppm Mono Laser Printer Manual Del Usuario preview
ML-2240 - 23 Ppm Mono Laser Printer
Brand: Samsung Pages: 82
Samsung ML-2150 Servicing Precautions preview
ML-2150
Brand: Samsung Pages: 8
Samsung ML-1610 - B/W Laser Printer User Manual preview
ML-1610 - B/W Laser Printer
Brand: Samsung Pages: 134
Samsung ML-1610 - B/W Laser Printer Manual Del Usuario preview
ML-1610 - B/W Laser Printer
Brand: Samsung Pages: 112
Samsung ML-1210 Manual Del Usuario preview
ML-1210
Brand: Samsung Pages: 128
Samsung ML ML-4551N Manual Del Usuario preview
ML ML-4551N
Brand: Samsung Pages: 152
Samsung ML 3471ND - B/W Laser Printer User Manual preview
ML 3471ND - B/W Laser Printer
Brand: Samsung Pages: 207
Samsung ML 2150 - B/W Laser Printer Manual Del Usuario preview
ML 2150 - B/W Laser Printer
Brand: Samsung Pages: 237
Samsung ML 3471ND - B/W Laser Printer Manual Del Usuario preview
ML 3471ND - B/W Laser Printer
Brand: Samsung Pages: 103
Samsung ML 2150 - B/W Laser Printer User Manual preview
ML 2150 - B/W Laser Printer
Brand: Samsung Pages: 217
Samsung ML-2010 - B/W Laser Printer Manual Del Usuario preview
ML-2010 - B/W Laser Printer
Brand: Samsung Pages: 122
Samsung SCX-5315F Service Manual preview
SCX-5315F
Brand: Samsung Pages: 103
Palram Applications OLYMPIA 3x3.05m/10 Instructions Manual preview
OLYMPIA 3x3.05m/10
Brand: Palram Applications Pages: 65
Saab B205 Installation Instructions Manual preview
B205
Brand: Saab Pages: 10
S+S Regeltechnik AERASGARD RCO2-W Manual preview
AERASGARD RCO2-W
Brand: S+S Regeltechnik Pages: 7
Wasp WPL608 Quick Start Manual preview
WPL608
Brand: Wasp Pages: 2
Xerox ColorQube 8580 System Administrator Manual preview
ColorQube 8580
Brand: Xerox Pages: 93

Brands by name

Popular brands

Load more brands