Epson R320 - Stylus Photo Color Inkjet Printer Service Manual Download Page 18

Page: 18 / 114

EPSON Stylus Photo R320

Revision B

TROUBLESHOOTING

Unit Level Troubleshooting

Table 1-7. Check Points for Paper Jam Error to Each Phenomenon

Occurrence

Timing

Position of CR

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

At power-on

Anywhere

"PF Motor" does not work at all.

PF Motor

1. Check if "PF Motor Connector Cable" is connected to

CN9 on "Main Board".

2. Check if the coil resistance of "PF Motor" is

approximately 3.0

Ω

with a tester. Refer to Table 1-1.

3. Check if "PF Motor Connector Cable" is damaged.

1. Connect "PF Motor Connector Cable" to CN9

on "Main Board".

2. Replace "PF Motor" with a new one.

3. Replace "PF Motor" with a new one.

Paper feeding operation is performed
normally, but paper is not sent into the
printer.

ASF Assy.

1. Check if "Roller, Retard Assy." operates properly while

feeding paper.

1. Reassemble "Extension Spring, 0.45" located

rear side of "Roller, Retard Assy.".

PE Sensor

1. Check if "Torsion Spring, 0.22" is not unfastened from

"PE Sensor Lever".

2. Check if "PE Sensor Cable" is not unfastened.

3. Check if "PE Sensor Cable" is correctly mounted on

"Holder, Shaft, LD Roller".

4. Check if "PE Sensor Cable" is not damaged.

1. Reassemble "Torsion Spring, 0.22"

2. Connect "PE Sensor" Connector to CN4 on

"Main Board".

3. Remount "PE Sensor Cable" correctly.

4. Replace "PE Sensor" with a new one.

Extension

Spring, 0.45

Torsion Spring, 0.22

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer



















































































































Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands

Epson R320 - Stylus Photo Color Inkjet Printer, Service Manual

Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands