Epson R320 - Stylus Photo Color Inkjet Printer Service Manual Download Page 39

Page: 39 / 114

EPSON Stylus Photo R320

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly

2.3.2 Removing Preview Monitor Unit

External View

Figure 2-3. Removing "Preview Monitor Unit"

Parts/Units which should be removed before removing "Preview Monitor
Unit"

None

Procedure for Removing

Raise the "Preview Monitor Unit".

Remove the screw(x1) which secure "Preview Monitor Unit".

Release the hook(x2) which secure "Preview Monitor Unit".
Then lift the "Preview Monitor Unit" upward.

Remove the "Monitor FFC" from the "Preview Monitor Board" connector.
Then remove "Preview Monitor Unit".

Preview Monitor Unit

C.B.P 3x8 (2-4kgf•cm)

Connector

Monitor FFC

Preview Monitor Board

Hooks

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer



















































































































Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands

Epson R320 - Stylus Photo Color Inkjet Printer, Service Manual

Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands