Epson R320 - Stylus Photo Color Inkjet Printer Service Manual Download Page 42

Page: 42 / 114

EPSON Stylus Photo R320

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly

When removing "Housing, Middle", the grounding spring may
detach and drop from "Main Board Unit". If this occurs,
reattach it to its original position referring to the following
figure.

Figure 2-8. Reattaching the Ground Spring

"Fixed spring, Core" should be attached with fixing the "Ferrit
Core" as shown below.

Figure 2-9. Reattaching the Fixed spring, Core

Grounding Spring

Ferrite Core

Fixed spring, Core

Make sure that "Panel FFC" is securely set and it is not reaching
the upper edge of the rib of "Housing, Middle" as shown in the
figure.

Figure 2-10. Mounting "Panel FFC"

Make sure that the connector cable of "Power Supply Board" is
securely set in the groove of "Housing, Lower".

Figure 2-11. Mounting the Connector Cable

Make sure that "Panel FFC" is not stuck under "Housing,
Middle".

Make sure to tighten up the screws on the back of "Housing,
Middle" in the order as shown in the figure.

Rib

Keep some clearance here.

Connector Cable

Groove

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer



















































































































Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands

Epson R320 - Stylus Photo Color Inkjet Printer, Service Manual

Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands