Epson R320 - Stylus Photo Color Inkjet Printer Service Manual Download Page 92

Page: 92 / 114

EPSON Stylus Photo R320

Revision B

ADJUSTMENT

Adjustment Except Adjustment Program

3.3 Adjustment Except Adjustment Program

Following is adjustment except Adjustment Program.

3.3.1 PG Adjustment

[Purpose]

This adjustment is required when removing or replacing the following parts/units in
order to secure the specified space between the print-side of the Print Head and the
paper.

Carriage Unit

CR Guide Shaft

Bushing, Parallel Adjust, Left (Right)
(Including when having moved "Bushing Parallel Adjust, Left (Right)")

[Adjustment Procedure]

Make both sides of the two Thickness Gauge (1.15mm and 1.31mm) clean by
wiping with Bemcot with a little alcohol.

To make the PG position minus (-), turn the gear of "APG Assy." and match the
flag centre of "Cam, CR, Right" with "PG Sensor".

Figure 3-5. Setting PG Position

Match the 0 position (Hole point of gear) of "Bushing, Parallel Adjust, Left
(Right)" with the rib of "Frame, Main".

Figure 3-6. Setting "Bushing, Parallel Adjust"

Move "Carriage Unit" to the centre of the printer and remove "Lever, Cartridge".
Then, set the PG-Adjustment Dummy Cartridge.

Gear of "APG Assy."

Cam, CR, Right

Flag

PG Sensor

Bushing, Parallel Adjust, Left

Ribs

Hole point

Bushing, Parallel Adjust, Right

Ribs

Hole point

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer



















































































































Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands

Epson R320 - Stylus Photo Color Inkjet Printer, Service Manual

Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands