Epson R320 - Stylus Photo Color Inkjet Printer Service Manual Download Page 77 | Manualshive

Page: 77 / 114

background image

EPSON Stylus Photo R320

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly

77

2.3.20 Removing Paper Guide, Front/Roller EJ Assy.

External View

Figure 2-59. Removing "Paper Guide, Front"/"Roller EJ Assy." (1)

Parts/Units which should be removed before removing "Paper Guide,
Front"/"Roller EJ Assy."

Paper Support Assy./Preview Monitor Unit/Housing, Upper/Housing, Middle/
Main Board Unit/ASF Assy./Holder, Shaft Assy./APG Assy./Print Head/
Carriage Unit/Printer Mechanism/CDR Guide Assy.

Procedure for Removing

1.

Release the hook of "Link EJ, Right" from the groove of "Guide, Shaft, Frame
EJ, Right". Then, remove "Link EJ, Right".

2.

Remove the flat washer which secures the right side of "Frame EJ Assy.".

3.

Remove "PF Timing Belt" from "Spur Gear, 37.242", then remove "Spur
Gear, 41.48".

4.

Remove "Compression Spring, 1.27" and "Holder, Idle Roller" together with
"PF Timing Belt".

5.

Move back "Carriage Unit" to the home position, and then remove "Frame EJ
Assy." in the direction of the arrow, also in the order indicated in the figure.

6.

Remove the flat washer which secures "Link EJ, Left", then Slide "Link EJ,
Left" to the right.

7.

Remove "Extension Spring, Push Up, Plate, Left" from the hooks of "Guide,
Shaft, Frame EJ, Left" and "Frame, Main".

8.

Release the hooks (Left x3, right x2) which secure "Guide, Shaft, Frame EJ,
Left (Right)". Then, remove "Guide, Shaft, Frame EJ, Left (Right)".

Compression

Spring, 1.27

Holder, Idle Roller

Spur Gear, 41.48

PF Timing Belt

Spur Gear,37.242

Link EJ, Right

Flat Washer

Guide, Shaft, Frame EJ, Right

Hook

1

2

Frame EJ Assy.

Hooks

Hook

Extension Spring,

Push Up, Plate, Left

Guide, Shaft,

Frame EJ, Left

Hooks

Link EJ, Left

Flat Washer

C A U T I O N

When removing "Frame EJ Assy.", take care not to damage or
transform "Star Wheels" of "Frame EJ Assy.".

«
...
75
76
77
78
79
...
»

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer



















































































































Reviews:

No comments

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brand: Xerox Pages: 73

Brand: Xerox Pages: 2

Brand: Waycon Pages: 8

ML 2851ND - B/W Laser Printer

Brand: Samsung Pages: 179

ML 2510 - B/W Laser Printer

Brand: Samsung Pages: 84

ML 1740 - B/W Laser Printer

Brand: Samsung Pages: 152

ML 1630 - B/W Laser Printer

Brand: Samsung Pages: 142

ML 1630 - B/W Laser Printer

Brand: Samsung Pages: 82

Brand: Samsung Pages: 414

scx-4100 series

Brand: Samsung Pages: 8

SCX-4600 Series

Brand: Samsung Pages: 121

Brand: AA Products Pages: 8

Brand: ICON ProAudio Pages: 29

Brand: Aroflora Pages: 36

Brand: Primera Pages: 2

Brand: TP Pages: 10

Brand: AOR Pages: 29

Brand: EVA Logik Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands