Epson R320 - Stylus Photo Color Inkjet Printer Service Manual Download Page 11

Page: 11 / 114

EPSON Stylus Photo R320

Revision B

TROUBLESHOOTING

Troubleshooting with LED/LCD Indications and Status Monitor 3 Message

Paper Out Error

Paper load error. Load correctly and
press Maintenance.

This error is detected when the leading edge of
paper cannot be detected with the PE Sensor in
a paper loading.

Paper Jam Error

(Including CD/DVD)

A paper jam has occurred. See your
printer's documentation for
information about clearing the jam.

This error is detected when ;

1. The posterior end of paper cannot be

correctly detected with the PE Sensor in a
paper loading.

2. The rear of CD/DVD cannot be correctly

detected with the Star Wheel/CDR Sensor in
a CD/DVD loading.

Maintenance Request

Service required.
Printer parts are at end of service life.
See printer manual for details.

This error is detected when the value of the
Waste Ink Pad Counter A set in EEPROM
reaches its limit (Variable between 20000 and
46750 points).

Table 1-3. LED/LCD Indication and STM3

Printer status

Maintenance

LED indication

LCD indication

STM3 message

Condition for error detection

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer



















































































































Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands

Epson R320 - Stylus Photo Color Inkjet Printer, Service Manual

Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands