Epson R320 - Stylus Photo Color Inkjet Printer Service Manual Download Page 78

Page: 78 / 114

EPSON Stylus Photo R320

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly

External View

Figure 2-60. Removing "Paper Guide, Front"/"Roller EJ Assy." (2)

Remove "Extension Spring, Push Up, Plate, Right" from the hooks (x2) of
"Guide, Shaft, Frame EJ, Right".

10. Release the hook which secures "Paper Guide, Front", then remove "Paper

Guide, Front".

11. Remove the "Porous Pad, Paper Guide, Front", "Porous Pad, Paper Guide,

Left", and "Porous Pad, Paper Guide, Front, Support"(x3) with tweezers from
"Paper Guide, Front".
(Refer to 2.3.5 Removing Porous Pad, Paper Guide, Front, Left, Support)

Guide, Shaft, Frame EJ, Right

Hooks

Extension Spring, Push Up, Plate, Left

Paper Guide, Front

Roller, PF Assy.

Hook

C A U T I O N

Do not touch "Porous Pad, Paper Guide, Front".

Do not damage the rib located on the upper surface of "Paper
Guide, Front".

Take care not to damage the surface of "Roller, PF Assy.".

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer



















































































































Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands

Epson R320 - Stylus Photo Color Inkjet Printer, Service Manual

Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands