Epson R320 - Stylus Photo Color Inkjet Printer Service Manual Download Page 9 | Manualshive

Page: 9 / 114

background image

EPSON Stylus Photo R320

Revision B

TROUBLESHOOTING

Troubleshooting with LED/LCD Indications and Status Monitor 3 Message

9

1.2 Troubleshooting with LED/LCD Indications and Status Monitor 3 Message

This section describes the LED/LCD indication, the STM3 message and the error condition when the printer detects an error in each operation such as the power on, the paper
loading/feeding and the ink absorption operation.

Table 1-3. LED/LCD Indication and STM3

Printer status

Maintenance

LED indication

LCD indication

STM3 message

Condition for error detection

Communication Error

--

--

This error is detected when the printer cannot
communicate with the PC properly.

Ink Low Condition

Blink

(Ink icon blinks)

Note :
Printing operation can be performed until it becomes ink
end condition even after the error message is displayed on
STM3. However, the Head Cleaning operation may not be
performed due to the Ink Low condition.

This error is detected when the ink consumption
reaches about 90%.

(Note)
When the Ink Low Condition is detected, the
Maintenance LED will blink. The printer will
continue to keep this LED status even if a new
Ink Cartridge is installed in the Ink Cartridge
replacement position. However, this LED status
will be reset (LED off) when "Carriage Unit"
returns to the home position.

«
...
7
8
9
10
11
...
»

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer



















































































































Reviews:

No comments

Related manuals for R320 - Stylus Photo Color Inkjet Printer

BTL7-S5 B-M Series

Brand: Balluff Pages: 14

BML-S1G0 7 M5E 0 Series

Brand: Balluff Pages: 194

Brand: Banner Pages: 12

Brand: Valore Pages: 5

Brand: DataCard Pages: 2

Brand: ICC Pages: 32

Brand: Oki Pages: 572

proColor pro900DP

Brand: Oki Pages: 127

Brand: OKIDATA Pages: 4

Brand: Quadratec Pages: 8

Brand: QVS Pages: 1

Brand: Warrior Winches Pages: 17

Brand: Xerox Pages: 3

Brand: Xerox Pages: 13

Brand: Xerox Pages: 41

Versant 3100 Press

Brand: Xerox Pages: 45

Brand: Zhiyun Pages: 10

Brand: Kabuto Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands