Epson R320 - Stylus Photo Color Inkjet Printer Service Manual Download Page 74

Page: 74 / 114

EPSON Stylus Photo R320

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly

2.3.19 Removing Ink System

External View

Figure 2-55. Removing "Ink System" (1)

Parts/Units which should be removed before removing "Ink System"

Paper Support Assy./Preview Monitor Unit/Housing, Upper/Housing, Middle/
Main Board Unit/ASF Assy./Holder, Shaft Assy./Printer Mechanism

Procedure for Removing

Take off the acetate tape, then release the connector cable of "Star Wheel/
CDR Sensor".

Remove the screws (x2) which secure "Support Plate, Frame, Main", and
remove "Support Plate, Frame, Main".

Remove the screw which secures "Cap Assy.".

Slide "Cap Assy." inward "Printer Mechanism" and release the dowels
(

: x2"). Then, remove "Cap Assy." from the ribs (x2) of "Frame Main".

Release the hooks (x3) and the dowels (x3) which secure "Pump Assy.", and
hold "Lever, Change Assy." and all the gears with your finger in order not to
let them drop, then remove "Cap Assy." and "Pump Assy." together.

Remove "Combination Gear, 20.82, 24", "Spur Gear, 27.2", "Lever, Change
Assy." and "Combination Gear, 27.2, 19.2" from "Pump Assy.".

Remove "Spur Gear, 25.6" from "Lever, Change".

Remove "Compression Spring, 2.36" from the dowel of "Lever, Change".

Support Plate,

Frame, Main

C.B.P 3x8

(5-7kgf•cm)

Dowels

Cap Assy.

C.B.S 3x6

(7-9kgf•cm)

Acetate Tape

Pump Assy.

Hooks

Dowels

Lever, Change Assy.

Ribs

Dowel

Hook

Sealing Rubber Part

Cleaner Head

Combination Gear, 27.2, 19.2

Spur Gear, 27.2

Combination

Gear, 20.82, 24

Silicon Material Part

Spur Gear, 25.6

Compression Spring, 2.36

Dowels

Lever, Change

C A U T I O N

Do not remove the ink tube which is connected to "Cap Assy."
and "Pump Assy.".

The ink tube cannot be removed from "Pump Assy." since it is
secured with silicon material for the following reasons.

To prevent "Pump Assy." from ink leakage.

To adjust the length of the ink tube extended from "Pump
Frame".

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer



















































































































Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands

Epson R320 - Stylus Photo Color Inkjet Printer, Service Manual

Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands