Epson R320 - Stylus Photo Color Inkjet Printer Service Manual Download Page 24

Page: 24 / 114

EPSON Stylus Photo R320

Revision B

TROUBLESHOOTING

Unit Level Troubleshooting

Table 1-11. Check Points for Fatal Error to Each Phenomenon

Occurrence Timing

Position of CR

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

At power-on

Out of HP

"CR Motor" does not work at all when
turning on the power.

CR Motor

1. Check if "CR Motor Connector Cable" is connected to

CN8 on "Main Board".

2. Check if "CR Motor Connector Cable" is damaged.

1. Connect "CR Motor Connector Cable" to

CN8 on "Main Board".

2. Replace "CR Motor" with a new one.

"Carriage Unit" strikes on "Lever,
Change" because the lever is leaning
forward when turning on the power.

PF Motor

1. Check if "PF Motor Connector Cable" is connected to

CN9 on "Main Board".

2. Check if the resistance of "PF Motor" is approximately

3.0

Ω

using a tester. Refer to Table 1-1.

3. Check if "PF Motor Connector Cable" is damaged.

1. Connect "PF Motor Connector Cable" to CN9

on "Main Board".

2. Replace "PF Motor" with a new one.

3. Replace "PF Motor" with a new one.

Ink System

1. Check if "Compression Spring, 2.36" of "Lever, Change"

has not come off.

1. Replace "Ink System" with a new one.

"Carriage Unit" strikes on "Paper Guide,
Upper" which has come off from "Main
Frame" when turning on the power.

Paper Guide,

Upper

1. Check if "Paper Guide, Upper" has come off from "Main

Frame".

1. Reassemble "Paper Guide, Upper" to "Main

Frame".

At power-on

Anywhere

"Carriage Unit" strikes on the right side
of "Main Frame" when turning on the
power.

CR Scale

1. Check if "CR Scale" has come off, or it properly passes

through the slit of "CR Encoder Sensor Board".

1. Reassemble "CR Scale" correctly.

* If the problem is not solved, replace

"Main Board" with a new one.

Lever, Change

Compression Spring, 2.36

Paper Guide, Upper

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer



















































































































Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands

Epson R320 - Stylus Photo Color Inkjet Printer, Service Manual

Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands