Epson R320 - Stylus Photo Color Inkjet Printer Service Manual Download Page 93

Page: 93 / 114

EPSON Stylus Photo R320

Revision B

ADJUSTMENT

Adjustment Except Adjustment Program

Move "Carriage Unit" to the left edge of the printer, then set the Thickness Gauge
(1.15mm) on the left ribs (X3) of "Paper Guide, Front".

Figure 3-7. Setting Thickness Gauge

Implement PG Adjustment on the left according to the flowchart in the Figure 3-8.

Figure 3-8. PG Adjustment (Left Side)

Remove the Thickness Gauge and move "Carriage Unit" to the right edge. Then,
set the Thickness Gauge on the right ribs (X3) of "Paper Guide, Front".

Figure 3-9. Setting Thickness Gauge

Implement PG Adjustment on the right according to the flowchart in the Figure
3-10.

Figure 3-10. PG Adjustment (Right Side)

Thickness Gauge

Ribs

Yes

Note:

Take down toward the printer front by 1 notch:
PG gets narrower.
Take up toward the printer back by 1 notch:
PG gets wider.

Take up: PG gets wider

Take down: PG gets narrower

Take down "Bushing, Parallel

Adjust, Left" toward the

printer front by 1 notch.

Go to Step 7.

Start

Take up "Bushing, Parallel

Adjust, Left" toward the

printer back by 1 notch.

Move "Carriage Unit" to

the right by using

"Timing Belt".

Does the Thickness

Gauge move?

Yes

Move "Carriage Unit" to

the right by using

"Timing Belt".

Does the Thickness

Gauge move?

Thickness Gauge

Ribs

Yes

Take up:

PG gets wider

Take down: PG

gets narrower

Start

Move "Carriage Unit" to
the left by using "Timing

Belt".

Does the Thickness

Gauge move?

Note:

Take down toward the printer front by 1 notch:
PG gets narrower.
Take up toward the printer back by 1 notch:
PG gets wider.

Take down "Bushing, Parallel

Adjust, Right" toward the

printer front by 1 notch.

Go to Step 9.

Take up "Bushing, Parallel

Adjust, Right" toward the

printer back by 1 notch.

Move "Carriage Unit" to
the left by using "Timing

Belt".

Does the Thickness

Gauge move?

Yes

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer



















































































































Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands

Epson R320 - Stylus Photo Color Inkjet Printer, Service Manual

Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands