Epson R320 - Stylus Photo Color Inkjet Printer Service Manual Download Page 69

Page: 69 / 114

EPSON Stylus Photo R320

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly

Make sure that "Waste Ink Pads" (x6) are set correctly to
the rib and the dowel of "Housing, Lower".

Figure 2-48. Reinstalling "Waste Ink Pads" (1)

Waste Ink Pad, Upper (Top)
Waste Ink Pad, Lower (Bottom)

Waste Ink Pad, Small

Cap, Ink Pad, Lower,
Small (Top)

Cap, Ink Pad, Lower,
Large (Bottom)

Figure 2-49. Reinstalling "Waste Ink Pads" (2)

After checking "Waste Ink Tube" is under "Waste Ink Pad,
Lower", put the jig on the indicated points in the figure
below, then install "Porous Pad, Ink Eject, Upper, Support".

Figure 2-50. Reinstalling "Porous Pad, Ink Eject, Upper, Support"

Jig

Porous Pad, Ink Eject,

Upper, Support

Waste Ink Pad, Lower

Adjusting Point

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer



















































































































Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands

Epson R320 - Stylus Photo Color Inkjet Printer, Service Manual

Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands