Epson R320 - Stylus Photo Color Inkjet Printer Service Manual Download Page 50

Page: 50 / 114

EPSON Stylus Photo R320

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly

2.3.9 Removing ASF Assy.

External View

Figure 2-21. Removing "ASF Assy." (1)

Parts/Units which should be removed before removing "ASF Assy."

Paper Support Assy./Preview Monitor Unit/Housing, Upper/Housing, Middle/
Main Board Unit

Procedure for Removing

Take off the Acetate Tape. Then remove connector cable of "PF Motor" and
"PG Motor" from the hook on "ASF Assy".

Remove the screws (Screw, Frame, Main) (x3) which secure connector cable
of "PF Motor" and "PG Motor". Then release the connector cable.

Remove the screws (x5) which secure "ASF Assy.". Then, remove "ASF
Assy." to the back of the printer.

ASF Assy.

Connector Cable

Screw, Frame, Main (5-7kgf.cm)

C.B.S (P4) 3x8 (8-10kgf•cm)

Hook

Acetate Tape

Screw, ASF

(4-5kgfcm)

C.B.S 3x6 (5-7kgf.cm)

C.B.P 3x8 (5-7kgf.cm)

C.B.S (P4) 3x8 (5-7kgf•cm)

C.B.P 3x8 (5-7kgf•cm)

C.B.S 3x6 (5-7kgf•cm)

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer



















































































































Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands

Epson R320 - Stylus Photo Color Inkjet Printer, Service Manual

Search results

Summary of Contents for R320 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R320 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands