manualshive.com logo in svg

ENCAD T-200, Service Manual

The ENCAD T-200 Service Manual is the essential resource for troubleshooting and maintaining your printer. Download this comprehensive manual for free from our website, and easily find step-by-step instructions and detailed diagrams to keep your machine in optimal working condition.

Share
Download
background image

ENCAD T-200 and T-200+ Service Manual

Assembly\Disassembly

5-28

15. Fit the Compression Spring over the post at the back of the Y-Arm

Assembly.

16. Fit the notch in the front end of the Frame Tensioner over the notch

in the front of the Y-Arm Assembly.

17. Depress the back of the Frame Tensioner and slip the Carriage Belt

over the Servo Motor pulley.  Make sure that the guides in the

Carriage Belt are properly fitted over the Servo Motor pulley.

18. Gently move the Carriage Assembly from end to end and make sure

that the Carriage Belt is not rubbing against any other parts.

Removing the Trailing Cable

1. Remove the Top Cover.

2. Remove the Trailing Cable Cover.

3. Remove the Right Cover Assembly.

4. Disconnect the Trailing Cable connector at the J6 location on the

MPWA.  Use the thumb and forefinger to pull forward on the

connector lock and remove the Trailing Cable from the connector.

5. With a flathead screwdriver, press the Electronics Cover tab located

in the upper slot on the left side of the Carriage Assembly. See

Figure 5-9. Lift up on the front left side of the Carriage Cover until

it comes part way off of the Carriage Assembly.  Then lift up on the

front right side of the Carriage Cover and move the Carriage Cover

slightly to the left so that the back of it clears the Back Support

Bracket.

6. Lift up on the connector lock to unlock the Trailing Cable connector

(J6) on the Carriage PWA and remove the end of the Trailing Cable.

7. Remove the Trailing Cable and Strain Relief from the Carriage

Assembly by releasing the latch on the left lower side of the Strain

Relief and lifting it off of the Carriage Assembly.  See Figure 5-10.

8. Pull the Trailing Cable away from the double-sided tape on the

Stabilizer Bracket.  Remove the Trailing Cable from the plotter

unit.

Summary of Contents for T-200



































































































































































Reviews:

No comments

Related manuals for T-200

Brands by name

Popular brands

Load more brands