Emerson Rosemount CT5100 Reference Manual Download Page 57

Page: 57 / 179

Figure 5-6: Power Gland

A. Purge power and alarm entry point

B. Power entry point

Two sources of electrical power are applied to the analyzer:

•

A purge electrical and alarm supply that is used to power the overpressure facility in the
electrical compartment of the analyzer. Refer to

Figure 5-6

(Item A).

•

An instrumentation electrical supply that is used to power all other functions of the
analyzer. See

Figure 5-6

(Item B).

The customer supplied circuit breakers

must

be in accordance with ATEX / IECEx / North

American protection concepts. The main power isolator controls the application of
electrical power to the purge controller with the secondary power isolator controlling the
application of electrical power to the remaining analyzer functions.

Reference Manual

Install

00809-0100-4512

October 2019

Reference Manual

Summary of Contents for Rosemount CT5100




















































































































































































Search results

Summary of Contents for Rosemount CT5100

Reviews:

Related manuals for Rosemount CT5100

Brands by name

Popular brands

Emerson Rosemount CT5100, Reference Manual

Search results

Summary of Contents for Rosemount CT5100

Reviews:

Related manuals for Rosemount CT5100

Brands by name

Popular brands