Elster gas-lab Q1 Technical Documentation Manual Download Page 33

Page: 33 / 158

Primer

gas-lab

Page 25

4 Primer for impatient operators:

What do I have to do to

…?

Notice:

The following instructions are based on the assumption that you are in

the basic device menu.

4.1 ... view the gas quality error listing?

If the status LED blinks red or yellow or is steadily illuminated, the error listing

contains alarm or warning entries.

Proceed as described below to view the error listing:

1) Invoke the menu (subordinated items) via the Menu key.

2) Invoke the next Menu (other modules) via the Menu key

3) Press the rightward arrow key until you have selected the

Monitoring

item.

4) Press the Enter key.

The main display of the

Monitoring

module is invoked. The error with the

highest priority level is displayed. Scroll through the error listing using the

arrow keys.

5) Proceed to Chapter 5.3.2 should you need more detailed information. If you

would like to accept an error, proceed to the very next chapter.

There may be up to two error listings. In addition to the

Gas quality

error listing,

an error listing of the

Monitoring

module’s message processing is also available.

Always switch to the display of the next error listing via the

Next listing

item. Please refer to Chapter 5.3 for further information on the error listing of the

message processing.

Gas quality

error listing

Monitoring

error listing

Next listing

Summary of Contents for gas-lab Q1































































































































































Search results

Summary of Contents for gas-lab Q1

Reviews:

Elster gas-lab Q1, Technical Documentation Manual, Page: 33 / 158

Search results

Summary of Contents for gas-lab Q1

Reviews: