Electrolux EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles Service Manual Download Page 71

Page: 71 / 88

Electrolux

EFS – Dishwashing Systems Platform

Electrolux Professional

Electronic Dishwasher

SERVICE MANUAL

DOC. NO. 5956.446.06

Electrolux Professional

P.71/88

LU700A / WTU40A

Prog. 047

CY2

Cycle 2 parameters family.

Ln2

Long Wash Phase [min]

Sh2

Short Wash Phase [s]

CY3

Cycle 3 parameters family.

Ln3

Long Wash Phase [min]

Switch OFF and then switch ON the machine.

FL620WS / LV6WS / WT38WS

Prog. 048

1. Switch OFF and then switch ON the machine.
2.

CFG

Enter into CFG parameter family and set the following parameters.

tYP 0

Undercounter like working cycles.

boi 0

Atmospheric boiler.

doo 2

Front loading.

dFL 3

Default values for Undercounter models.

trc 1

SOFT START ENABLED.

b_t 1

Tank heater works only if boiler temperature reached.

btF 75

Enable filling tank by means of rinsing cycles.

LES 0

Detergent level switches not enabled.

ACTIVE function disabled

(up to version 3.11 set to

)

Regeneration cycle disabled (only for dishwashers with non-continuous water softener).

ALr 1

Alarms enabled.

3. Modify Communication and HACCP parameters:

HCP

Enter into

HCP

parameter family and set the following parameters.

sEr 9

Dishwasher with incorporated continuous water softener.

4. Switch OFF and then switch ON the machine.

Summary of Contents for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

























































































Search results

Summary of Contents for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Reviews:

Related manuals for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Brands by name

Popular brands

Electrolux EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles, Service Manual

Search results

Summary of Contents for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Reviews:

Related manuals for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Brands by name

Popular brands