Electrolux EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles Service Manual Download Page 41

Page: 41 / 88

Electrolux

EFS – Dishwashing Systems Platform

Electrolux Professional

Electronic Dishwasher

SERVICE MANUAL

DOC. NO. 5956.446.06

Electrolux Professional

P.41/88

WT830EA / WT850EA

Prog. 017

Switch OFF and then switch ON the machine.

CFG

Enter into CFG parameter family and set the following parameters.

tYP 2

Automatic Pot Washer.

boi 0

Atmospheric boiler.

doo 3

Automatic Pot Washer

dFL 2

Default values for Hood Type models.

trc 0

(for this appliance SOFT START is NOT possible).

b_t 1

Tank heater works only if boiler temperature reached.

btF 0

The tank is filled into the traditional way.

LES 0

Detergent level switches not enabled.

UI 9

Select user interface hood type model

(up to version 3.11 set to

)

rE 0

Regeneration cycle disabled.

ALr 1

Alarms enabled.

Switch OFF and then switch ON the machine.

Modify the cycle parameters:

CY1

Cycle 1 parameters family.

Ln1

Long Wash Phase [min]

Sh1

Short Wash Phase [s]

FP1 5

Final Pause [s]

CY2

Cycle 2 parameters family.

Ln2

Long Wash Phase [min]

Sh2

Short Wash Phase [s]

FP2 5

Final Pause [s]

CY3

Cycle 3 parameters family.

Ln3

Long Wash Phase [min]

Sh3

Short Wash Phase [s]

FP3 5

Final Pause [s]

Switch OFF and then switch ON the machine.

Summary of Contents for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

























































































Search results

Summary of Contents for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Reviews:

Related manuals for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Brands by name

Popular brands

Electrolux EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles, Service Manual

Search results

Summary of Contents for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Reviews:

Related manuals for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Brands by name

Popular brands