Electrolux EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles Service Manual Download Page 28

Page: 28 / 88

Electrolux

EFS – Dishwashing Systems Platform

Electrolux Professional

Electronic Dishwasher

SERVICE MANUAL

DOC. NO. 5956.446.06

Electrolux Professional

P.28/88

PW 1 - 2 / WT830 - 850

Prog. 005

Switch OFF and then switch ON the machine.

CFG

Enter into CFG parameter family and set the following parameters:

tYP 1

Pot Washer.

boi 0

Atmospheric boiler.

doo 2

Front loading function.

dFL 2

Default values for Pot Washer models.

trc 0

(for this appliance SOFT START is NOT possible).

b_t 1

Tank heater works only if boiler temperature reached.

btF 0

The tank is filled into the traditional way.

LES 0

Detergent level switches not enabled.

UI 9

Select user interface hood type model

(up to version 3.11 set to

)

rE 0

Regeneration cycle disabled.

ALr 1

Alarms enabled.

Switch OFF and then switch ON the machine.

Modify Factory parameters:

FAC

Factory parameters family

bt°C 78

Boiler Temperature Threshold.

Switch OFF and then switch ON the machine.

Summary of Contents for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

























































































Search results

Summary of Contents for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Reviews:

Related manuals for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Brands by name

Popular brands

Electrolux EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles, Service Manual

Search results

Summary of Contents for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Reviews:

Related manuals for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Brands by name

Popular brands