Electrolux EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles Service Manual Download Page 35

Page: 35 / 88

Electrolux

EFS – Dishwashing Systems Platform

Electrolux Professional

Electronic Dishwasher

SERVICE MANUAL

DOC. NO. 5956.446.06

Electrolux Professional

P.35/88

LS5WS / WT4WS TRIPHASE

Prog. 012

1. Switch OFF and then switch ON the machine.
2.

CFG

Enter into CFG parameter family and set the following parameters.

tYP 0

Hood Type like working cycles.

boi 0

Atmospheric boiler.

doo 2

Front loading door type.

dFL 3

Default values for Undercounter models.

trc 1

SOFT START ENABLED.

b_t 1

Tank heater works only if boiler temperature reached.

btF 75

Enable filling tank by means of rinsing cycles.

LES 0

Detergent level switches not enabled.

UI 13

Select user interface for LS5

(up to version 3.11 set to

)

rE 1

Regeneration cycle enabled.

ALr 1

ALARMS ENABLED.

3. Switch OFF and then switch ON the machine.
4. Modify Factory parameters:

FAC

Enter into FAC parameter family.

bt°C 83

Boiler Temperature Threshold.

bAJ 2

Boiler Temperature Adjust.

bSt 2

Booster Function.

5. Modify the cycle parameters:

CY3

Cycle 3 parameters family.

Ln3

Long Wash Phase [min]

Sh3 40

Short Wash Phase [s]

6. Switch OFF and then switch ON the machine.
7. Modify Detergent dosage:

GEn

Enter into GEn parameter family.

dIn 70

Initial Detergent Dosage [s].

rIn 5

Initial Rinse Aid Dosage [s].

Cnt

Counters

rCy 20

Number of cycles allowed before regeneration.

9. Switch OFF and then switch ON the machine.

Summary of Contents for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

























































































Search results

Summary of Contents for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Reviews:

Related manuals for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Brands by name

Popular brands

Electrolux EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles, Service Manual

Search results

Summary of Contents for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Reviews:

Related manuals for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

Brands by name

Popular brands